PowerTek MC642 Скачать руководство пользователя страница 57

Страница: 57 / 73

:SYSTem:BEEPer:STATe

Syntax:

:SYSTem:BEEPer:STATe <BOOL>
:SYSTem:BEEPer:STATe?

Description:

This command sets state of device beeper.

Parameters:

<BOOL>

{ON|OFF|1|0} (default 1)

device system beeper is enabled

OFF

device system beeper is disabled

same as ON

same as OFF

Remarks:

Overlapped command
Value is not affected by reset or by *RST command

Example:

SYST:BEEP:STAT ON
SYST:BEEP:STAT? Response: 1

:SYSTem:BEEPer:VOLume

Syntax:

:SYSTem:BEEPer:VOLume <DNPD>
:SYSTem:BEEPer:VOLume?

Description:

This command sets the system device beeper volume.

Parameters:

<DNPD>

Range 0.0 ... 1.0 (Max. volume) (default 0.2)

Remarks:

Overlapped command
Value is not affected by reset or by *RST command

Example:

SYST:BEEP:VOL 0.2
SYST:BEEP:VOL? Response: 2.000000E-01

:SYSTem:COMMunicate:BUS

Syntax:

:SYSTem:COMMunicate:BUS <CPD>
:SYSTem:COMMunicate:BUS?

Description:

This command selects communication interface.

Parameters:

<CPD>

{SERial|GPIB|USB|LAN} (default SER)

SERial

RS232 interface

GPIB

GPIB interface

USB

USB interface

LAN

LAN interface

Remarks:

Sequential command
Value is not affected by reset or by *RST command

Example:

SYST:COMM:BUS SER
SYST:COMM:BUS? Response: SER

Operation manual

Содержание MC642










































































Результаты поиска

Содержание MC642

Отзывы:

Бренды по названию

Популярные бренды

PowerTek MC642, Руководство по эксплуатации

Результаты поиска

Содержание MC642

Отзывы:

Бренды по названию

Популярные бренды