Power Sensors Limited PQube 3 Скачать руководство пользователя страница 99

Страница: 99 / 103

PQube 3 Instruction Manual

Page 99 of 103

Max_AN1_AN2_of_Interest_in_RMS_volts=AUTO*

*AUTO not yet available for this tag

Any number [volts]

Min_AN3_E_of_Interest_in_RMS_volts=AUTO*

Max_AN3_E_of_Interest_in_RMS_volts=AUTO*

The AUTO values are determined by the Dip and Swell
thresholds on Analog Channel 3.

*AUTO not yet available for this tag

AUTO

Any number [volts]

Min_AN4_E_of_Interest_in_RMS_volts=AUTO*

Max_AN4_E_of_Interest_in_RMS_volts=AUTO*

The AUTO values are determined by the Dip and Swell
thresholds on Analog Channel 4.

*AUTO not yet available for this tag

AUTO

Any number [volts]

Min_AN3_AN4_of_Interest_in_RMS_volts=AUTO*

Max_AN3_AN4_of_Interest_in_RMS_volts=AUTO*

The AUTO values are determined by the AN3-AN4 Dip
and Swell thresholds.

*AUTO not yet available for this tag

AUTO

Any number [volts]

Min_Temperature_of_Interest_in_DegC=0

Max_Temperature_of_Interest_in_DegC=50

Set the minimum and maximum temperature for viewing
in Trends and Statistics recordings if the AUTO setting
does not provide a suitable graph.

Any number [degrees
°C]

Min_Humidity_of_Interest_in_%_RH=0

Max_Humidity_of_Interest_in_%_RH=100

Set the minimum and maximum relative humidity in %
for viewing in Trends and Statistics recordings.

Any number [%RH]

Max_Voltage_Unbalance_of_Interest_in_Percent=10
%

Set the full scale Voltage Unbalance in Trends and
Statistics recordings.

Any number [%]

Max_Current_Unbalance_of_Interest_in_Percent=99
%

Set the full scale Current Unbalance in Trends and
Statistics recordings.

Any number [%]

Max_Voltage_THD_of_Interest_in_Percent=10%

Set the full scale THD voltage in Trends and Statistics
recordings.

Any number [%]

Max_Current_TDD_of_Interest_in_Percent=25%*

Set the full scale TDD current in Trends and Statistics
recordings.

Any number [%]

Max_Flicker_of_Interest=4

Set the full scale RMS Flicker in Trends and
Statistics recordings.

Any number

Shop for Power Metering products online at:

1.877.766.5412

www.

PowerMeterStore

.ca

Содержание PQube 3








































































































Результаты поиска

Содержание PQube 3

Отзывы:

Бренды по названию

Популярные бренды

Power Sensors Limited PQube 3, Инструкция по эксплуатации

Результаты поиска

Содержание PQube 3

Отзывы:

Бренды по названию

Популярные бренды