manualshive.com logo in svg

Power Sensors Limited PQube 3, Инструкция по эксплуатации

Поделиться
Скачать
Power Sensors Limited PQube 3 Скачать руководство пользователя страница 68

PQube 3 Instruction Manual 

Page 68 of 103 

5.8

 

Maintenance 

5.8.1

 

Turning Off Your PQube 3 

Your PQube 3 is designed to be a permanently installed monitor.  It does not have an on/off switch 
because it is designed to run continuously.   If you need to turn off your PQube  3,  remove your 
PQube 3’s instrument power (either the power screw terminal block on your PQube 3, the optional 
PM1 Power Supply Module, or PoE).  Your PQube 3 will automatically initiate graceful shutdown to 
prevent any write damage to flash.   

If you have a UPS module installed, your PQube 3 will continue to run for the allotted amount of 
time.  To immediately power down the device while on backup power from the UPS module, go to 
the Actions screen and press Reboot.  With no permanent power source available, your PQube 3 
will simply turn off.

 

5.8.2

 

Replacing Your PQube 3’s Clock Battery 

Your  PQube  3  uses  a  user-replaceable,  non-rechargeable 
lithium-manganese  coin  cell  battery  to  back  up  the  system 
clock in the event of instrument power loss.  PSL recommends 
replacing  this  battery  every  10  years.    When  you  order  a 
replacement  battery,  always  remember  to  power  off  the 
device  first,  disconnect  mains  connections,  and  verify 
disconnections. 

To remove and replace the battery, insert a small flat-head screwdriver to pry up the label near the 
USB port and microSD card slot.  Remove the old battery and install the new one.  It is not possible 
to install the battery with the wrong polarity.   

Follow all applicable federal, state, and local regulations when disposing of the used battery. 

Disconnect power to the device before replacing the battery.

 

Replace battery with a PSL-supplied battery only.  Use of another battery may present a 

risk of fire or explosion.   This part must be supplied only by PSL or PSL agents.  

5.8.3

 

Life Expectancy of the PQube 3 and the PM1 module 

The estimated life expectancy of a PQube 3 and its PM1 module is 8 years (estimation based on 
operating temperature at 20-30degC). 

5.8.4

 

UPS1 Life Expectancy and Long Term Storage Instructions 

The lithium ion batteries in your UPS1 module are rated for 3 years or 500 cycles, whichever comes 
first.  Contact PSL to replace the batteries.  Do not attempt to replace the batteries yourself. 

If you need to store your PQube 3 and modules on the shelf for 3 months or longer, all you need to 
do is charge your UPS1 module up to full before putting it away.  Simply turn on your PQube 3 with 
the UPS1 module, and let it run for at least 20 hours to ensure a full charge.   

If  you  will  be  storing  your  PQube  3  and  modules  for  more  than  1  year,  be  sure  to  periodically 
recharge your UPS1 module at least once per year to avoid full discharge. 

Shop for Power Metering products online at:

1.877.766.5412

www.

PowerMeterStore

.ca

Содержание PQube 3








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды