background image

 

 

Page 19 

Please notice that if the XP system is improperly turned off before a complete 
boot  up  procedure,  the  above  preset  power  on  control  functions  will  be 
disabled until next turning off after a complete boot up. 

 

Storage Device 

 

The standard system storage device is 2.5” SATA HDD in the main unit. This 
device can be replaced with an option SATA SSD HDD. 

 

TECHNICAL MANEUVERS 

Some  technical  maneuver  in  XP-3000/3300  series  such  as  serial  COM  port 
+5V/+12V  power  supply  settings  is  supported  in  system  jumper  setting  and 
printer  parameter  setting.  However,  such  support  is  limited  to  the  application 
of  specific  Posiflex  peripherals  and  must  be  disabled  when  the  Posiflex 
peripherals are disconnected.

 

Failure to follow the discipline would result in 

electric or fire hazard and such consequences are not covered by product 
warranty!

  

 

The  rest  applicable  technical  maneuvers  include  system  CMOS  data  reset, 
system  reset,  DRAM  upgrades  and  installation  of  optional  SATA  SSD.

 

All 

these  technical  maneuver operations require purchase of applicable Technical 
Manual  from  Posiflex  or  consultation  from  Posiflex  authorized  dealers  and 
should be handled only by a 

qualified technician

 

 

警告使用者

警告使用者

警告使用者

警告使用者

 

這是甲類的資訊產品,在居住的環
境 中使 用 時 , 可 能會 造 成 射 頻干
擾,在這種情況下,使用者會被要

求採取某些適當的對策。

 

T31454 

Содержание XP-3000 Series





















Отзывы: