Porsche 928S 1983 Скачать руководство пользователя страница 47

Страница: 47 / 110

Luggage compartment door

(See notes under "Alarm system" if your car
is equipped with an alarm system.)

To open the door

Insert key into the lock and turn it to the right
and lift the door. Two gas-struts will then
open the door fully.

To close the door

Push the door down until it can be heard to
lock.

Never drive with the luggage compartment

door ajar or open, as then exhaust fumes
could enter the vehicle.

Engine compartment Hood top

To release the hood

Pull the lever on the left hand cowl side
panel underneath the instrument panel.

To open the hood

Lift the hood top slightly and release the

safety catch by pressing the lever upwards.

Make sure the windscreen wipers are not
tilted forward!

When the vehicle lights are on, a lamp on the
underside of the hood top lights automati-
cally.

Содержание 928S 1983















































































































Результаты поиска

Содержание 928S 1983

Отзывы:

Бренды по названию

Популярные бренды

Porsche 928S 1983, Руководство пользователя

Результаты поиска

Содержание 928S 1983

Отзывы:

Бренды по названию

Популярные бренды