manualshive.com logo in svg

Porsche 928S 1983, Руководство пользователя

Поделиться
Скачать
Porsche 928S 1983 Скачать руководство пользователя страница 10

Alarm system 

If your car is equipped with an alarm system 
you will have received two S-keys instead of 
the normal master keys. The alarm system 
can be activated only with the S-key by lock-
ing the doors or closing the luggage com-
partment door and turning the key to the 
left. If the doors are locked with the auxiliary 
key then the door will be mechanically lock-
ed but there is no contact to activate the 

alarm. The alarm system is switched off au-
tomatically when a door or the luggage com-
partment is opened with the S-key. If the lug-
gage compartment door is opened while the 
alarm system is switched on, the key must 

be turned to the left to reactivate the alarm 

system. If the drivers or passenger side door, 
engine compartment hood or the luggage 
compartment door is opened while the 

alarm is activated a specially protected siren 
will sound for about 30 seconds. The engine 
cannot be started. 

In the interest of safety the S-Key should ne-

ver be lent out to other persons. For this rea-
son the fuel filter cap can only be locked 
with the auxiliary key. This key can be used 
as a"workshop key" and can also be handed 
over at filling and service stations. 

9 

Application Positions 

Door Locks 

Steering/Starter 
ignition switch 

Luggage 
Compartment 
Door Lock 

Tank Filler Cap 

Switching Alarm system on and off. 
Locking and unlocking the doors. 

Lockable. 

Switching alarm system on and off. Opening lug-
gage compartment door. 

Only lockable with an auxiliary key. 

The S-Key should, for reasons of safety, not be 

lent out to other persons 

Glove 
Compartment 

Lockable. 

Содержание 928S 1983















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды