Porsche 928S 1983 Скачать руководство пользователя страница 104

Страница: 104 / 110

500-2000 km
(300-1200 miles)

then at and every

20000 km (12000 miles)

Change engine oil and filter.

Manual gearbox: Change oil

every 80000 km (50000 miles)

Manual and automatic gearboxes: Check oil level

Automatic gearbox: Change oil, replace filter

every 40000 km (24000 miles)

Automatic gearbox: Check level of hypoid oil in differential housing, oil change every 80000 km

Check engine and gearbox for leaks.

Steering: Check tightness and function of all connections to steering gear, trackrods, and idler arms
and also check the condition of the protecting covers.
Check fluid level in steering servo unit, and check unit for leaks.

Exhaust system: Check flanges for proper seating.

Check for leaks in exhaust system.

Check play in front wheel bearings.

Fuel system: Renew fuel filter and check fuel lines for leaks.

Check tyre pressure.

Check ignition timing.

Check carburation with exhaust gas analyzer.

Check battery acid level. Check headlight adjustment and function of blinker, brake and back lights, as

well as wipers and horn. Check washer jets and fluid level in wash system (anti-freeze). Top up wash sys-
tem solution.

Treat the door, hood and roof seals after removing the ground away rubber particles. Check door check-
straps.

Check function of central warning unit.

Check function of heating, ventilation and air conditioning, both driver and passenger sides.

107

Содержание 928S 1983















































































































Результаты поиска

Содержание 928S 1983

Отзывы:

Бренды по названию

Популярные бренды

Porsche 928S 1983, Руководство пользователя

Результаты поиска

Содержание 928S 1983

Отзывы:

Бренды по названию

Популярные бренды