manualshive.com logo in svg

Porsche 928S 1983, Руководство пользователя

Поделиться
Скачать
Porsche 928S 1983 Скачать руководство пользователя страница 35

With the ignition turned on (engine not run-
ning) all individual warning lights and the 
central warning light must come on to indic-
ate operational readiness. If the engine oil 

level is too low the central warning light will 

flash, (lack of engine oil can, in comparison 
with all other functions, only be checked 
with the engine turned off and with the vehi-

cle level.) 

The warning light for the brakelights must go 
out with the first brake application. The 

remaining lights go out when the engine is 

started. 

By pressing the button (arrow) in the middle 
of the console the central warning light can 
be turned off in the case of priority 2 mal-
functions. It cannot be turned off in priority 1 
cases because immediate action is neces-
sary to rectify the fault. 

When the handbrake is applied or not fully 
released the central warning light cannot be 
turned off. Only when the handbrake is fully 

released does the central warning light go 

out. 

Note: If the vehicle is tow or roll started the 
warning lights will not go out. The engine 
must be turned off and restarted with the 
ignition key. 

33 

Содержание 928S 1983















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды