Porsche 928S 1983 Скачать руководство пользователя страница 26

Страница: 26 / 110

Fuel Gauge

With the ignition turned on the gauge shows
the amount of fuel in the tank. If the level is too
low the fuel warning light comes on.

Warning light

The warning light comes on when about 8 liters

(7 Imp. qts) are left in the tank. The tank should
be filled at the next opportunity.

Warning Lights

(see also Central Warning Unit)

TAIL LAMP

The warning light comes on when a tail light
ceases to function.

STOP LAMP

The warning light comes on when the ignition
is switched on and must go out after the first
brake application. If a brake light bulb is defec-
tive the warning light will not go out.

WASH FLUID

The warning light comes on before the screen-
wash water runs out, indicating that about 2

liters (1.75 Imp. qts.) of water remain.

COOLANT

The coolant warning lamp lights up as soon
as the coolant level in the expansion tank drops

below the minimum permissible level. The

warning lamp may come on when the car is
started and then go out again after a short

time. This is due to the volume of the coolant

increasing as it warms up, and thus exceeding

the minimum permissible coolant level.

It is essential to top up the coolant and, if ne-

cessary, to have the cooling system checked
for leaks.

Consult the chapter on the cooling system.

PARKING LIGHTS

This light comes on in the Combi-lnstrument
when the sidelights are turned on and goes
out again when the headlights are turned on.

Trailer Indicator Light

The blinker warning light for the trailer opera-
tion flashes at the same frequency as the blin-

ker lights. Should a trailer blinker fail the fre-

quently is noticeably quicker.

Содержание 928S 1983















































































































Результаты поиска

Содержание 928S 1983

Отзывы:

Бренды по названию

Популярные бренды

Porsche 928S 1983, Руководство пользователя

Результаты поиска

Содержание 928S 1983

Отзывы:

Бренды по названию

Популярные бренды