POLTI Vaporetto SMART 100_B, Инструкция по эксплуатации, Страница: 28 / 92

10.1 BRIGHTENING UP CURTAINS AND
DRAPES
Mites and dust can be removed from curtains
and drapes by steaming the fabric with just
the handle. The steam can remove odours
and brighten up colours, allowing the fabric
to be washed less frequently.
For this surface, set the steam to level
minimum.
10.2 REMOVING STAINS FROM CARPETS
AND UPHOLSTERY
Direct the steam directly onto the stain with
the greatest angle possible (never vertically
with respect to the surface to be cleaned)
and place a cloth beyond the stain to collect
the dirt that has been “blown” away by the
steam pressure.
For this surface, set the steam to level
minimum.
10.3 TAKING CARE OF PLANTS AND
HUMIDIFYING ROOMS
To care for your house plants, remove the
dust from the leaves using the steam. Steam
the surface directly from the handle, at a
minimum distance of 50 cm, adjust the steam
to the minimum level.
Plants breathe better and will be cleaner and
brighter. Furthermore, you can also use the
steam to refresh interior areas, especially
those used by smokers.
11. OUT OF WATER
A lack of water in the boiler is indicated by
the out-of-water light B (8) coming on.
To resume use, simply:
- switch off and disconnect the Vaporetto.
- fill the tank as described in Section 1.
- connect the Vaporetto and turn it back on.
12. GENERAL MAINTENANCE
Before carrying out any maintenance on the
device, always unplug it from the power
mains making sure that the product has
cooled down before proceeding.
To clean the outside of the appliance, use
only a damp cloth and tap water.
All accessories can be cleaned using running
water, ensuring they are completely dry
before the next use.
Do not use detergents of any type.
After using the brushes, we recommend
letting the bristles cool down in their natural
position, in order to avoid any deformation.
13. CLEANING THE BOILER
(special maintenance)
To maintain optimum performance, clean the
boiler every 10/20 uses depending on the
amount of limestone in the water.
13.1 Unplug the appliance and let it cool down
for 2 hours at least, if it is hot.
13.2 Empty the water tank to prevent leakage.
13.3 Place the appliance on its side and
unscrew the boiler cap protection (18)
located on the side of the appliance.
13.4 Unscrew the boiler cap (19).
13.5 Pour 250 ml of cold water (20) into the
boiler using the funnel supplied.
13.6 Rinse the boiler and pour the water into
the sink or into a special container. If the
water is very dirty, repeat the operation until
it is clean.
13.7 Insert 100 ml of water in the boiler and
screw on the boiler cap and the boiler cap
protection, ensuring that they are correctly
screwed on.
13.8 Refill the water tank.
13.9 Turn the appliance back on.
Before using steam to clean, direct the jet
into a sink or other container until the steam
is completely clean.
WARNING: Steam.
Risk of scalding!
WARNING: Risk of scalding! When
accessing the boiler (removing the cap,
filling up, emptying), ensure that the
appliance is switched off at the power
switch and disconnected from the mains for
at least two hours.
WARNING: Do not exceed the quantity of
water recommended and pour it slowly into
the boiler, paying attention not to let it
overflow.
WARNING: Steam.
Risk of scalding!
WARNING: This operation must always be
done after having disconnected the appliance
from the mains.
WARNING: Do not pour toxic substances,
acids, solvents, detergents, corrosive
substances and/or explosives or perfumes
into the boiler.
E
N
G
L
IS
H
| 28 |