Polaris Alpha Скачать руководство пользователя страница 6

Страница: 6 / 56

Description of Interfaces

3-1 Appearance

Figure 3-1

No.

Description

SMA connector for RTK antenna.

Status LED. There are three states shown for Alpha as Rover

Base data not received: flashes two times followed by 1 sec of silence.

In process of finding RTK solution: flashes with frequency at 1Hz or 4 Hz depends on the RTK

ratio is in between 1 and 3 or in between 3 and 5.

RTK solution found: remain lighted continuously.

This LED is always off when Alpha is configured as Base.

LED for indicating the TTL UART interface is selected.

LED for indicating the USB interface is selected.

LED for indicating the Bluetooth interface is selected.

Push button for interface selection. Each time the button is clicked, the selected interface toggles.

Press this button for more than 3 seconds will enable/stop logging measurement data to SD Card.

Slide switch for choosing the operating mode, see section 4-4 for details.

6-pin TTL connector for Base-to-Rover or Rover-to-UAV applications, see section 3-2 for details.

Micro USB connector

SD card status LED. When the SD card is inserted, this LED will flash and record raw measurement

data to the SD card, until number of files on the SD card reaches 129. In this case the LED lights up

continuously, and recording stops. If no SD card is inserted, the LED is off.

Micro SD card connector for raw measurement data recording.

4-pin TTL connector for aerial survey applications. See section 3-3 for details.

Table 3-1

Содержание Alpha

























































Результаты поиска

Содержание Alpha

Отзывы:

Polaris Alpha, Руководство пользователя, Страница: 6 / 56

Результаты поиска

Содержание Alpha

Отзывы: