Polaris Alpha Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 56

Polaris Alpha Скачать руководство пользователя страница 56

56

The  information  provided  is  believed  to  be  accurate  and  reliable.  These  materials  are  provided  to  customers  and  may  be  used  for
informational  purposes  only.  No  responsibility  is  assumed  for  errors  or  omissions  in  these  materials,  or  for  its  use.  Changes  to
specification can occur at any time without notice.

These  materials are  provides

“as is” without warranty of any kind, either expressed or implied, relating to sale and/or use including

liability or warranties relating to fitness for a particular purpose, consequential or incidental damages, merchantability, or infringement of
any patent, copyright or other intellectual property right. No warrant on the accuracy or completeness of the information, text, graphics
or other items contained within these materials. No liability assumed for any special, indirect, incidental, or consequential damages,
including without limitation, lost revenues or lost profits, which may result from the use of these materials.

The product is not intended for use in medical, life-support devices, or applications involving potential risk of death, personal injury, or
severe property damage in case of failure of the product.

«
...
54
55
56

Содержание Alpha

























































Отзывы:

Нет отзывов