Polaris Alpha Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 56

Polaris Alpha Скачать руководство пользователя страница 14

14

Base

USB/TTL mode / switch on A

TTL or Micro-USB

RTK

antenna

Telemetry

Radio

Telemetry

Radio

Rover

TTL mode / switch on B

RTK

antenna

Pin #2 of 6-pin

TTL connector

Setup for Real-Time Controller over Telemetry Radio

433MHz/915MHz/2.4GHz

Alpha RTK

Alpha

RTK

. . .

Real-Time
Controller

Pin #3 of 6-pin

TTL connector

Figure 4-6

For line-of-sight precision guidance applications that do not use Mission Planner with MAVLink

protocol as in figure 4-6, user can configure one Alpha RTK receiver as RTK base and use 6-pin UART

connector port or micro-USB port to connect to a telemetry radio for sending correction data to the

RTK rover. Another Alpha RTK receiver is configured as RTK rover, using pin-2 of the 6-pin connector to

connect to another telemetry radio for receiving correction data from the RTK base, and using pin-3 of

the 6-pin connector to send RTK NMEA message output to the real-time controller.

«
...
12
13
14
15
16
...
»

Содержание Alpha

























































Отзывы:

Нет отзывов