Polaris Alpha Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 56

Polaris Alpha Скачать руководство пользователя страница 19

19

6. RTK Setup

6-1 Introduction

Typical uses of Alpha RTK receiver are (1) rover-only: Alpha works with a 3

rd

party RTK correction data

provider, (2) base/rover pair: two Alphas are configured as a base and a rover, respectively.

For rover-only usage, Alpha RTK receiver can be used with RTK base station service providers having

Virtual Reference Station (VRS) service, or a physical RTK base station within 10Km distance. Typical

setup would be to use an Alpha RTK rover connecting via Bluetooth to Android phone running NTRIP

Client that connects with RTK base station over Internet. Alpha can work with popular Trimble and

Leica base stations.

For base/rover pair usage, the applications could be: (1) an Alpha RTK receiver setup as local RTK base

at some known reference location to serve other Alpha RTK receiver rovers within 10Km distance, (2)

An Alpha RTK receiver first connecting to RTK base station service to determine its position accurately

then later setup as local RTK base to serve other Alpha RTK receiver rovers within 10Km distance.

«
...
17
18
19
20
21
...
»

Содержание Alpha

























































Отзывы:

Нет отзывов