Polaris Alpha Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 56

Polaris Alpha Скачать руководство пользователя страница 40

40

6-4-6

Real-Time Guidance Configuration Using Locally Setup Base/PC and Phone Connection

For longer range non-line-of-sight real-time control application, NTRIP Internet connection

can be used to send RTK base data.

Base

USB mode / switch on A

Micro-USB

cable

Internet

Bluetooth

Rover

BT mode / switch on B

NTRIP

caster

NTRIP

client

3G/4G/LTE

RTK

antenna

RTK

antenna

. . .

Alpha RTK

Alpha RTK

Setup for Real-Time Controller over Internet

Real-Time
Controller

Pin #3 of 6-pin

TTL connector

Figure 6-21

Use section 6-2 method to configure one Alpha receiver into RTK rover. Depending on what’s available

to determine base antenna position, select one of the options to configure the second Alpha RTK

receiver into RTK base as described in section 6-3.

Use the same method as described in section 6-4-3 to setup base/rover Internet NTRIP connection

capability. Connect RTK rover UART output on pin-3 and GND on pin-6 of the 6-pin connector to the

real-time controller, then it’s ready to use!

«
...
38
39
40
41
42
...
»

Содержание Alpha

























































Отзывы:

Нет отзывов