Polaris Alpha Скачать руководство пользователя страница 52

Страница: 52 / 56

Field

Description

Example

Port

Select the COM port for base data input

COM5

Bitrate (bps)

Serial port data input bit rate.

115200

Byte Size

Byte Size depends on serial settings.

8 bits

Parity

Parity depends on serial settings.

None

Stop Bits

Stop Bits depends on serial settings.

1 bit

Flow Control

Flow control depends on serial settings.

None

Table A-3-1

Setup an output stream of type "NTRIP Caster" and press the "Opt" button to set the output

stream options.

Figure A-3-3

Set the output stream options as follows. Press the OK button to return to the STRSVR dialog

when finished. The

blue color Mountpoint, User-ID and password

are specified by user, and rover

can access the base data with this authentication info later on.

Field

Description

Example

NTRIP Caster Host

Grey-out for STRSVR will use local WAN IP

as host IP

None

Port

Enter the port used by Caster.

5000

Mountpoint

Enter Caster mount point name

my_RTK_base

User-ID

Enter user ID to access the base data

test

password

Enter password to access the base data

1234

Table A-3-2

Содержание Alpha

























































Результаты поиска

Содержание Alpha

Отзывы:

Polaris Alpha, Руководство пользователя, Страница: 52 / 56

Результаты поиска

Содержание Alpha

Отзывы: