background image

14

AU

Telephone Helpline: 1300225960

Fault

Probable Cause

Solution

The appliance is 

leaking water

The appliance is not properly levelled

Adjust the screw feet to level the appliance 

(if applicable)

The discharge outlet is blocked

Clear the discharge outlet

Movement of water to the drain is 

obstructed

Clear the floor of the appliance 

(if applicable)

The water container is damaged

Call POLAR agent or qualified Technician

The appliance is 

unusually loud

The appliance has not been installed 

in a level or stable position

Check installation position and change if 

necessary

Loose nut/screw

Check and tighten all nuts and screws

Technical Specifications

Model

Voltage

Power

Current

Capacity

Dimensions

H x W x D

Refrigerant

Weight

(kg)

CK640-A

220-240V~ 50Hz

500W

4.0A

3 x GN2/3

410 x 660 x 650

R290 150g

42

Electrical Wiring

The plug is to be connected to a suitable mains socket.

POLAR appliances are wired as follows:

•  Live wire (coloured brown) to terminal marked L

•  Neutral wire (coloured blue) to terminal marked N

•  Earth wire (coloured green/yellow) to terminal marked E

The appliances must be earthed.

If in doubt consult a qualified electrician.

Electrical isolation points must be kept clear of any obstructions. In the event of any emergency 

disconnection being required they must be readily accessible.

Compliance

The product must not be disposed of as household waste. To help prevent possible harm to human 

health and/or the environment, the product must be disposed of in an approved and environmentally safe 

recycling process. For further information on how to dispose of this product correctly, contact the product 

supplier, or the local authority responsible for waste disposal in your area.

POLAR parts have undergone strict product testing in order to comply with regulatory 

standards and specifications set by international, independent, and federal authorities.

POLAR products have been approved to carry the following symbol:

All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, 

mechanical, photocopying, recording or otherwise, without the prior written permission of POLAR.

Every effort is made to ensure all details are correct at the time of going to press, however, POLAR reserve the right to 

change specifications without notice.

CK640-A_A5_v1_20190507.indb   14

2019/5/7   15:55

Содержание CK640-A

















Отзывы: