manualshive.com logo in svg

Polar Refrigeration CK640-A, Инструкция по эксплуатации, Страница: 5 / 16

Поделиться
Скачать
Polar Refrigeration CK640-A Скачать руководство пользователя страница 5

5

AU

AU

Telephone Helpline: 1300225960

Insert the food probe 

•  Before selecting which cycle to use, the probe must be inserted into the food. This allows the internal 

temperature of the food to be measured. 

•  It is important that the probe is correctly connected to the unit.

Note: To prevent bacterial contamination or contamination of any other 

biological nature, the needle probe must be disinfected after use.

Control Panel

Alarm LED

Minute LED

Degree 

Celsius LED

Degree 

Fahrenheit LED

Timed 

Chilling LED

Set-Temperature 

Chilling LED

Storage LED

In the “on” state, during normal operation, the display shows:

•  the amount of time remaining for a timed blast chilling operation, if this is ongoing

•  the temperature measured by the pin probe if a set-temperature chilling operation is ongoing

•  the temperature of the cabinet, if storage is ongoing.

In “stand-by” mode, during normal operation, the display shows the temperature of the cabinet for ½ 

second every 3 seconds.

Signals

LED

Message

Timed Chilling LED
•  If on and the LED 

 is off, a timed chilling operation is ongoing

•  If on and the LED 

 is also on, a post timed-chilling storage operation is ongoing

•  If flashing, a timed chilling and storage cycle will have been selected
Set-temperature chilling LED
•  If on and the LED 

 is off, a set-temperature chilling storage operation is ongoing

•  If on and the LED 

 is also on, a post set-temperature chilling storage operation will 

be ongoing

•  If flashing, a set temperature chilling and storage cycle will have been selected

CK640-A_A5_v1_20190507.indb   5

2019/5/7   15:55

Содержание CK640-A

















Отзывы:

Нет отзывов