Planmeca ProMax Pan/Ceph Скачать руководство пользователя страница 48

Страница: 48 / 100

- 48 -

NOTE: The new shoulder number should be lower than old number.

Press

Lock

and take the pin out and then press

Done

. Take another exposure

and check ball size again. If not repeat until correct size.

2.1.b 10

Ball

Measure from the center of the Center Ball to the center on the 10

Ball on

the right then measure from the center of the Center Ball to the center of 10

Ball on the left. (Figure 82)

Figure 82

NOTE: From the Center Ball, the distance left or right to the 10

Ball will always need to be the

same.

2.1.b.i

Too Left

If the distance from the Center Ball to the left is more than the
right, then move the table away from the column. (Figure 83).

Figure 83

Printed copies of this document are considered uncontrolled.

22811.20.Rev001 07.31.2018

Содержание ProMax Pan/Ceph





































































































Результаты поиска

Содержание ProMax Pan/Ceph

Отзывы:

Похожие инструкции для ProMax Pan/Ceph

Бренды по названию

Популярные бренды

Planmeca ProMax Pan/Ceph, Руководство по калибровке

Результаты поиска

Содержание ProMax Pan/Ceph

Отзывы:

Похожие инструкции для ProMax Pan/Ceph

Бренды по названию

Популярные бренды