Planmeca ProMax Pan/Ceph Скачать руководство пользователя страница 17

Страница: 17 / 100

- 17 -

Chapter

Computer Connections

Ethernet

Connect a crossover cable to the Ethernet port on the back of the ProMax. (Figure 17)

Figure 17

Connect the other end of the crossover cable into the Ethernet port on the back of the
computer.

NOTE: If using a PCI card then follow the above instructions but instead use a PCI Interface Cable.

Didapi Configuration

Click Start , All Programs, Planmeca and then Didapi Configuration (Figure 18)

Figure 18

Click on Ethernet Interface.

The default ip address is:

192.168.0.130

Click on “ProMax Open device config file” and type in:

Localhost=(ip address):5000

Save the file, click “Refresh” and close Didapi Configuration

Printed copies of this document are considered uncontrolled.

22811.20.Rev001 07.31.2018

Содержание ProMax Pan/Ceph





































































































Результаты поиска

Содержание ProMax Pan/Ceph

Отзывы:

Похожие инструкции для ProMax Pan/Ceph

Бренды по названию

Популярные бренды

Planmeca ProMax Pan/Ceph, Руководство по калибровке

Результаты поиска

Содержание ProMax Pan/Ceph

Отзывы:

Похожие инструкции для ProMax Pan/Ceph

Бренды по названию

Популярные бренды