Pionetics LINX 140T Скачать руководство пользователя страница 3

Consumer Install 12.16.2016 

Section 1.    Safety Precautions 

 
 

 

The LINX 140T system should be installed, serviced and maintained to comply with state and local laws 
and regulations and in conformance with this owner’s manual. 

 

 

Read and follow all instructions carefully before using the LINX 140T Drinking Water System. 

 

 

DO NOT open the cell lids or outer enclosure when the LINX 140T system is powered.    There is a risk 

of electrical shock.

 

 

 

If the detachable power cord is damaged, it must be replaced.

 

 

 

Install LINX systems upright (not on their side).    Use with cold feed water ONLY (33-100˚F; 1-40˚C). 

 

 

DO  NOT  use  with  water  that  is  microbiologically  unsafe  or  of  unknown  quality  without  adequate 

disinfection before or after the systems. 

 

 

The systems are designed to operate with supply water pressure in the range of 20-100 psi (130-690 kPa).   

If the pressure exceeds 100 psi (690 kPa), a pressure regulator must be installed.

 

 

 

These systems are not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 
instruction concerning use of the systems by a person responsible for their safety.

 

 

 

Children should be supervised to ensure that they do not play with the systems. 

 

 

Grounding  Instructions:  These  systems  must  be  properly  grounded.  In  the  event  of  a  malfunction, 
grounding will reduce the risk of electric shock.    These systems are equipped with a cord having an 
equipment-grounding conductor and a grounding plug.    The plug must be plugged into an appropriate 
outlet that is installed and grounded in accordance with all local codes and ordinances.     

 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 

Warning:

    Improper connection of the equipment-grounding conductor can result in a risk of 

electric shock.    Check with a qualified electrician if you are in doubt whether the systems are 
properly grounded.    Do not modify the plug provided with the systems. If the plug will not fit 
the outlet, have a proper outlet installed by a qualified electrician. 

Содержание LINX 140T
























Отзывы: