Pinguely-Haulotte HA20PX Скачать руководство пользователя страница 209

Страница: 209 / 282

CORRECTIVE MAINTENANCE SHEET

CHANGING THE BASKET

Sheet C053

Caution!

It is essential to put the

component in slings before

dismantling/re-assembling

it.

1 - Preliminary operations

•

Put the machine in the maintenance configuration (see corresponding
paragraph).

•

Switch off electric power (see corresponding paragraph).

•

Disconnect the « - » then « + » terminals of the starter battery.

2 - Removing the platform

•

Disconnect the platform control panel electric wiring harness.

•

Remove the control panel fixing screws (17).

•

Remove the control panel and its silent blocks (18).

•

Remove the platform’s electric plug (19), if any, by unscrewing its fixing
bolts.

•

Put the platform in slings.

•

Remove the pre-stressing stop by unscrewing the screw (1) and nut (2).

Upper part

•

Remove the Nylstop nut (3) and its washer (4) on the platform side.

•

Remove the stop pad (5) on the platform side.

•

Remove the weighing articulation pin (6).

Lower part

•

Remove the lower pivot pin (7) by removing its fixing screws (8) and
washer (9).

•

Remove the platform and retain the ball (10), the nylatron washer (11) and
the stop (12).

•

If necessary, unscrew the pre-stressing nut totally (13) as a safety
measure, before performing any operation on the platform.

3 - Installing the platform

•

Check the condition of the elastic parts and wearing parts, and replace if
necessary (spring washers (14), collar rings (15), ring (16), nylatron
washer (11), control panel silent blocks, circlips).

Lower part

•

If necessary, adjust the pre-stressing system by tightening the pre-stres-
sing nut (13), so that the washers are 108 mm high (see figure 3).

•

Put the platform into place, taking care to put the ball (10), nylatron
washer (11) and stop (12) in the right places.

•

Lubricate the bore and put the lower pivot (7) into place. Fix using the
fixing screw (8) and washer (9).

NB:

Only use lubricants recommended by the manufacturer.

Upper part

•

Lubricate then put back the weighing articulation pin (6).

•

Put back the stop tab (5).

•

Install the Nylstop nut (3) and its washer (4).

•

Adjust the stop for the pre-stressing system by tightening the screw (1)
and the nut (2).

•

Put the control panel into place on its silent blocks and fix using the
screws equipped with new washers.

•

Reconnect the control panel wiring harness.

Sheet C053

Folio 1/3

Содержание HA20PX



























































































































































































































































































Результаты поиска

Содержание HA20PX

Отзывы:

Похожие инструкции для HA20PX

Бренды по названию

Популярные бренды

Pinguely-Haulotte HA20PX, Руководство по ремонту

Результаты поиска

Содержание HA20PX

Отзывы:

Похожие инструкции для HA20PX

Бренды по названию

Популярные бренды