Pinguely-Haulotte HA20PX Скачать руководство пользователя страница 261

Страница: 261 / 282

CORRECTIVE MAINTENANCE SHEET

Folio 1/2

CHANGING THE BASKET ROTATION GEARING

Sheet C104

Caution!

It is essential to put the

component in slings before

dismantling/re-assembling it.

1 - Preliminary operations

•

Put the machine in the maintenance configuration (see corresponding
paragraph).

•

Switch off electric power (see corresponding paragraph).

•

Remove the basket (see corresponding sheet).

•

Remove the basket rotation hydraulic motor (see corresponding sheet).

2 - Removing the gearing

•

Remove the motor fixing flange (1).

•

Remove the endless screw (2) and the adjusting washers (3), if any.

•

Remove the screw (4) and the toothed washer (5).

•

Remove the end cap (8), then the platform link part (9) and the Nylatron
washer (10).

•

Remove the nylstop nut (11), bushing (12), elastic washers (13), plate
(14).

•

Remove the articulation pin assembly (15) then the disk (16) and pad (17).

•

Remove the screws and washers (18) and (19) and remove the pin (15),
wormwheel (6), keys (21), hub (20), key (7),

3 - Installing the gearing

•

Change the rings, pads and keys if necessary.

•

Put into place on the articulation pin (15) the key (7), hub (20) keys (21),
wormwheel (6), and put back the screws and washers (18) and (19).

•

Put into place the disk (16) and pad (17), then the articulation pin assem-
bly (15).

•

Put into place the plate (14), elastic washers (13), bushing (12), then a
new nylstop nut (11).

•

Put into place the Nylatron washer (10), platform link part (9), end cap (8)
and Stauff collar.

•

Fix the assembly with the screw (4) equipped with a new toothed washer
(5).

•

Put back the endless screw (2) and the adjusting washers (3) if necessary.

•

Put back the motor fixing flange (1).

•

Put back the basket rotation hydraulic motor (see corresponding sheet).

•

Put back the basket (see corresponding sheet).

•

Lubricate the gearing.

NB:

Only use lubricants recommended by the manufacturer.

•

Put the machine back in the operational configuration.

Содержание HA20PX



























































































































































































































































































Результаты поиска

Содержание HA20PX

Отзывы:

Похожие инструкции для HA20PX

Бренды по названию

Популярные бренды

Pinguely-Haulotte HA20PX, Руководство по ремонту

Результаты поиска

Содержание HA20PX

Отзывы:

Похожие инструкции для HA20PX

Бренды по названию

Популярные бренды