Pinguely-Haulotte HA20PX Скачать руководство пользователя страница 273

Страница: 273 / 282

CORRECTIVE MAINTENANCE SHEET

Folio 1/2

CHANGING THE JIB CYLINDER

Sheet C115

Caution!

Ensure that the oil is not too

hot.

Caution!

Use a container to collect oil

to prevent pollution of the

environment.

Caution!

It is essential to put the

component in slings before

dismantling/re-assembling it.

1 - Preliminary operations

•

Put the machine in the maintenance configuration (see corresponding
paragraph).

•

Switch off electric power (see corresponding paragraph).

•

Anchor the basket on the ground.

2 - Removing the jib cylinder

•

Put the cylinder (1) and jib vertical elements (2) and (3) in slings.

•

Mark and disconnect the jib cylinder’s two hydraulic hoses.

NB:

Unscrew the hoses slowly to release residual hydraulic pressure.

•

Put caps on the hoses.

•

Remove the two bolts and pin stop rings from the cylinder pin (4) on the
cylinder body side.

•

Remove the pin (4).

•

Remove the pin stop clevis from the cylinder pin (5) on the rod side.

•

Remove the pin (5).

•

Remove the jib cylinder (1).

3 - Installing the jib cylinder

NB:

Before re-installing, check the condition of all articulation pin rings
and replace if necessary. Lubricate all bores before re-installing the
pins. Only use lubricants recommended by the manufacturer.

•

Put the jib cylinder into place and put back the two articulation pins on the
rod and body side of the cylinder.

•

Put back the pin stop rings (4) and fix with their bolts.

•

Put back the pin stop clevis (5).

•

Remove the slings.

•

Reconnect the cylinder’s hydraulic hoses (1).

4 - Additional operations

•

Free the basket.

•

Put the machine back in the operational configuration.

•

Ensure that there is oil in the hydraulic tank.

•

Make several jib movements to test operation and purge the hydraulic cir-
cuit.

•

Check the level of the hydraulic circuit.

Содержание HA20PX



























































































































































































































































































Результаты поиска

Содержание HA20PX

Отзывы:

Похожие инструкции для HA20PX

Бренды по названию

Популярные бренды

Pinguely-Haulotte HA20PX, Руководство по ремонту

Результаты поиска

Содержание HA20PX

Отзывы:

Похожие инструкции для HA20PX

Бренды по названию

Популярные бренды