Pinguely-Haulotte HA20PX Скачать руководство пользователя страница 259

Страница: 259 / 282

CORRECTIVE MAINTENANCE SHEET

Folio 1/2

CHANGING THE SWING JOINT ASSEMBLY

Sheet C100

Caution!

Put the turntable rotation

blocking pin into place.

Caution!

It is essential to put the

component in slings before

dismantling/re-assembling

it.

Caution!

Ensure that the oil is not too

hot.

Caution!

Use a container to collect oil

to prevent pollution of the

environment.

1 - Preliminary operations

•

Lift the boom sufficiently to enable access to the swing joint.

•

Place wedges under the boom to bear its weight.

•

Put the machine in the maintenance configuration (see corresponding
paragraph).

•

Switch off electric power (see corresponding paragraph).

•

If necessary, close the shut-off valve or empty the hydraulic tank.

2 - Removing the swing joint

•

Open the chassis box, mark and disconnect all electric connectors (5).

•

Open the turntable box, mark and disconnect all electric connectors (6)
from the swing joint wiring harness.

•

Free the two electric wiring harnesses (2) of the swing joint after marking
their respective paths.

•

Mark and disconnect the hydraulic caps and hoses (1) of the swing joint
(3), on the turntable and below the chassis.

NB:

Unscrew hoses slowly to release residual hydraulic pressure.

•

Put caps on the hoses.

•

Put the swing joint in slings.

•

Remove the swing joint’s stop screw (4).

•

Remove the screws (7) fixing the swing joint to the chassis.

•

Remove the swing joint from underneath the chassis.

3 - Installing the swing joint assembly

•

Put the swing joint into place from underneath the chassis, and fix with
fixing screws equipped with new nylstop nuts.

•

Put back the swing joint rotation stop screw (4).

•

Reconnect the hydraulic hoses and caps on the swing joint according to
the marks made during dismantling.

•

Pass the wiring harnesses in the machine along their original paths.

•

Reconnect the electric connections in the chassis box and turntable box
according to the marks made during dismantling.

4 - Additional operations

•

Put the machine back in the operational configuration.

•

Remove the wedges from under the boom.

•

Make several steering and travel movements using all possible travel
speeds to purge the hydraulic circuit.

•

Check that the electric controls work properly.

•

Check the level of the hydraulic oil tank.

Содержание HA20PX



























































































































































































































































































Результаты поиска

Содержание HA20PX

Отзывы:

Похожие инструкции для HA20PX

Бренды по названию

Популярные бренды

Pinguely-Haulotte HA20PX, Руководство по ремонту

Результаты поиска

Содержание HA20PX

Отзывы:

Похожие инструкции для HA20PX

Бренды по названию

Популярные бренды