Phytec kitCON-161CS Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 62

background image

kitCON-161CS/JC/JI

44



PHYTEC Meßtechnik GmbH 1999 L-356e_2

9

The Battery Buffer

To prevent loss of data in case of sudden power failure the
kitCON-161CS/JC/JI can be equipped with a battery. This battery
buffers the memory devices on U10 and U11. However, this battery
buffer is not otherwise essential to the functioning of the
kitCON-161CS/JC/JI.

Position BT1 on the component side of the module is provided for
mounting a battery type CR2032. As of the pressing of this manual, a
lithium battery is recommended as it offers relatively high capacity at
low self-discharge. In the event of a power failure at VCC, the RAM
memory blocks will be buffered by a connected battery via VBAT.

The current consumption depends on the components populating the
board and memory size. For the standard devices used on the board
the draw is typically 1 µA (max. 100 µA) per RAM-device.

Regarding data and code integrity, please be advised that despite the
battery buffer, changes in the data content within the RAM can occur
given disturbances. The battery-buffer does not completely remove
the danger of data destruction.

Note:
Utilizing the battery buffer for the RAMs the storage temperature
is only 0

°

C to +70

°

C.

«
...
48
49
50
51
52
...
»

Содержание kitCON-161CS































































Отзывы:

Нет отзывов

Похожие инструкции для kitCON-161CS

Бренд: Acer Страницы: 12

Бренд: ASRock Industrial Страницы: 44

Бренд: NXP Semiconductors Страницы: 6

Бренд: VIA Technologies Страницы: 76

Бренд: Gigabyte Страницы: 80

Бренд: Watski Страницы: 43

Бренд: DAQ system Страницы: 52

Бренд: ASROCK Страницы: 97

Бренд: IDT Страницы: 18

Бренд: Parsun Страницы: 93

Бренд: Aaeon Страницы: 53

Бренд: Aaeon Страницы: 46

Бренд: EVGA Страницы: 35

Бренд: Rohm Страницы: 8

Бренд: ON Semiconductor Страницы: 20

Бренд: Maxim Страницы: 33

Бренд: TYAN Страницы: 35

Бренд: TYAN Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды