Phytec kitCON-161CS Скачать руководство пользователя страница 30

Страница: 30 / 62

kitCON-161CS/JC/JI



PHYTEC Meßtechnik GmbH 1999 L-356e_2

The jumpers (S3 = DIP-switch S3, JP = insertable jumper,
J = solderable jumper) have the following functions:

Default Setting

Alternate Setting

JP1

(1+2)

external ROM/Flash active

(2+3)

internal ROM/Flash active

JP2

(open)

CAN1

not connected to

DB9-plug P3

(1+2)

DB9-plug P3 for

(3+4)

second CAN-interface CAN1

JP3

(open)

CAN0

at P2 not

terminated

(closed)

CAN0

at P2 terminated with

120

Ω

resistor

JP4

(open)

CAN1

at P3 not

terminated

(closed)

CAN1

at P3 terminated with

120

Ω

resistor

JP5

(2+3) CAN-VCC

derived

from

supply voltage

(1+2)

CAN-VCC derived from CAN-
network via DB9-plug P2

JP6

(closed)

CAN-GND derived from
supply voltage

(open)

CAN-GND derived from CAN-
network via DB9-plug P2

JP7

(open)

CAN0

and CAN1

separate

(1+2)

CAN0

and CAN1

(3+4)

connected

JP8

(open)

J1850-driver regular
function

(closed)

J1850-driver in Loopback Mode

JP9

(open)

Pin 3 of DB9-plug P3 is
open

(1+2)

Pin 3 is J1850

-Bus

(2+3)

Pin 3 is GND (for CAN11)

JP10 (2+3)

supply voltage for J1850

driver derived from boards
supply voltage

(1+2)

supply voltage for J1850

driver

derived from external source via
connector X7

JP11
JP12

These jumpers configure the functions of ports P4.4 – P4.7 in consideration of the con-
troller mounted on the kitCON-161CS/JC/JI

JP13 (1+2)

/CS1 for RAM

(3+4)

/CS0 for FLASH

(2+4)

/CS1 for FLASH

(1+3)

/CS0 for RAM

(2+3)

256 kByte or 64 kByte
RAM

(1+2)

1 MB RAM

J8-
J10,
J13-
J15

(closed)

no ICE/connect-16x
installed

(open)

ICE/connect-16x installed on X2

J11,
J12

(closed)

AREF

and V

AGND

(closed)

derived from supply
voltage VCC and GND

(open)

AREF

and V

AGND

(open)

derived from external voltage
source via kitCON-Connector pins
61/65 and 62/66

In order to utilize the special features of a specific controller on the kitCON-161CS/JC/JI
other jumpers might be set additionally

The availability of this interface depends on the controller mounted on the kitCON-
161CS/JC/JI.

Содержание kitCON-161CS































































Результаты поиска

Содержание kitCON-161CS

Отзывы:

Похожие инструкции для kitCON-161CS

Бренды по названию

Популярные бренды

Phytec kitCON-161CS, Руководство по оборудованию

Результаты поиска

Содержание kitCON-161CS

Отзывы:

Похожие инструкции для kitCON-161CS

Бренды по названию

Популярные бренды