PGO BR-500 Скачать руководство пользователя

Страница: 296 / 330

- Loosen the 9 fixing screws
and remove the cleaner cap.

- Remove the filtering element.
- Replace the air filter with a
new one.

Check the blow-by and
condensate exhaust pipe and
empty it, if full.

Cleaning (Every

,000 Km):

- Wash with water and shampoo.

- Dry up by small compressed air jets and a clean cloth.

- Soak with 50% fuel and oil SELENIA AIR FILTER OIL mixture.

- Let the filtering element drip and press it with your hands without squeezing.

- Replace the filtering element.

N.B.

Failure to observe the rules regarding the filtering element cleaning could cause an

improper lubrication of the same.

A poor lubrication affects the filtering capacity.

An excessive lubrication causes a concentration of the carburetion.

Caution

If the vehicle has ridden on dusty roads, the air filter must be cleaned more

frequently than what indicated in the scheduled maintenance table.

Caution

Never let the engine run without air filter. This would cause an excessive wear of

cylinder and piston and would damage the carburettor.

PGO BR-500 ENGINE

P.3-16

PGO BR-500 ENGINE

Maintenance

Содержание BR-500











































































































































































































































































































































Результаты поиска

Содержание BR-500

Отзывы:

Похожие инструкции для BR-500

Бренды по названию

Популярные бренды

PGO BR-500, Руководство по обслуживанию

Результаты поиска

Содержание BR-500

Отзывы:

Похожие инструкции для BR-500

Бренды по названию

Популярные бренды