Pfeiffer Vacuum PrismaPro QMA 250 F1 Скачать руководство пользователя страница 43

Страница: 43 / 88

9 Maintenance

Maintenance in the Pfeiffer Vacuum Service Center

Pfeiffer Vacuum offers a complete maintenance service for all products.
Pfeiffer Vacuum recommends: Contact your Pfeiffer Vacuum Service Center to arrange the
maintenance of defective products and components.

Cleaning in the Pfeiffer Vacuum Service Center

Pfeiffer Vacuum recommends: Contact your nearest Pfeiffer Vacuum Service Center to ar-
range the cleaning of heavily-soiled products and components.

Loss of warranty claims

The following will result in the loss of the warranty:

● Damage to or removal of a closure seal
● Opening the device during the warranty period

Contact the Pfeiffer Vacuum Service Center in the event of process-related shorter mainte-
nance intervals.

First read through the sections completely

Read the section with the work instructions through completely first before you commence
with work.

9.1 Execution of maintenance work

Maintaining the analyzer QMA 250

The analyzer ages in normal use and does not require preventive or regular maintenance work.

► Carry out a visual inspection of the analyzer.
► Eliminate malfunctions and faults resulting from a contaminated ion source or from a contaminat-

ed analyzer using the degas function of the ion source or by baking out the analyzer.

► Check whether you can achieve better results with the settings from the test report before you

perform wide-ranging maintenance work.

– Inadequate sensitivity, malfunctions, and faults may also be due to incorrectly set ion source

parameters.

► Contact

Pfeiffer Vacuum Service

Maintaining the electronic unit QME 250

The QME 250 electronic unit does not normally require any repairs or maintenance.

► Contact

Pfeiffer Vacuum Service

9.2 Test report

The test report lists the ion source parameters which have achieved good results during the final in-
spection at the factory.

Maintenance

43/86

Содержание PrismaPro QMA 250 F1

























































































Результаты поиска

Содержание PrismaPro QMA 250 F1

Отзывы:

Бренды по названию

Популярные бренды

Pfeiffer Vacuum PrismaPro QMA 250 F1, Перевод оригинала

Результаты поиска

Содержание PrismaPro QMA 250 F1

Отзывы:

Бренды по названию

Популярные бренды