manualshive.com logo in svg

Pfeiffer Vacuum PrismaPro QMA 250 F1, Перевод оригинала

Поделиться
Скачать
Pfeiffer Vacuum PrismaPro QMA 250 F1 Скачать руководство пользователя страница 12

2 Safety

2.1 General safety information

The following 4 risk levels and 1 information level are taken into account in this document.

 DANGER

Immediately pending danger

Indicates an immediately pending danger that will result in death or serious injury if not observed.

► Instructions to avoid the danger situation

 WARNING

Potential pending danger

Indicates a pending danger that could result in death or serious injury if not observed.

► Instructions to avoid the danger situation

 CAUTION

Potential pending danger

Indicates a pending danger that could result in minor injuries if not observed.

► Instructions to avoid the danger situation

NOTICE

Danger of damage to property

Is used to highlight actions that are not associated with personal injury.

► Instructions to avoid damage to property

Notes, tips or examples indicate important information about the product or about this docu-
ment.

2.2 Safety instructions

Safety instructions according to product’s life stages

All safety instructions in this document are based on the results of a risk assessment. 
Pfeiffer Vacuum has taken into account all the relevant life stages of the product.

Risks during installation

 DANGER

Danger to life caused by electric voltage on the QME electronic unit

You may only attach the electronic unit to a correctly installed QMA analyzer (earth connection). The 
24 V supply line of the SP current supply may never be connected if the connection of the QMA Ana-
lyzer is not screwed tight to the QME electronic unit. Only qualified service personnel may open the 
QME electronic unit.

There are no parts in the QME electronic unit that should be maintained by the user.

► Install the QMA analyzer correctly before installing the QME electronic unit.
► Establish a correct earth connection between the components.
► Only have the QME electronic unit opened by qualified service personnel.
► Never operate the QME electronic unit when opened.

Safety

12/86

Содержание PrismaPro QMA 250 F1

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды