manualshive.com logo in svg

Pfeiffer Vacuum PrismaPro QMA 250 F1, Перевод оригинала

Поделиться
Скачать
Pfeiffer Vacuum PrismaPro QMA 250 F1 Скачать руководство пользователя страница 29

5 Installation

5.1 Installing PrismaPro

 DANGER

Danger to life due to electric voltage

High voltages are present inside the device. When touching parts that are live, there is a risk of 
death. If there is visible damage, there is a risk of death when commissioning the device.

► Work on the open device must only be carried out by trained specialist personnel.
► Before carrying out any installation and maintenance work, switch the device off and disconnect 

it from the current supply.

– After switching off, wait about 60 seconds and then disconnect all cables (power cable at the 

end).

► Never open the device with the current supply connected.
► Secure the current supply against unauthorized or unintentional reactivation.
► Do not insert any objects into the vent openings.
► Never open an external power supply pack.
► Never operate an open or defective device.
► Secure a defective device against accidental operation.
► Protect the device against moisture.

 DANGER

Danger to life from electric shock

Inadequate or incorrect grounding of the unit leads to contact-sensitive voltage on the housing. When 
making contact, increased leakage currents will cause a life-threatening electric shock.

► Before the installation, check that the connection leads are voltage-free.
► Conduct the electrical connection in accordance with locally applicable regulations.
► Make sure that the local mains voltage and frequency match rating plate specifications.
► Make sure that the mains cable and extension cable meet the requirements for double isolation 

between input voltage and output voltage, in accordance with IEC 61010 and IEC 60950.

► Use only a 3-pin mains cable and extension cable with properly connected protective earthing 

(earthed conductor).

► Plug the mains plug into a socket with earthing contact only.
► Always connect the mains cable prior to all other cables, to ensure continuous protective earth-

ing.

NOTICE

Impairment from contamination and damage

Touching the devices or components with bare hands increases the desorption rate and leads to in-
correct measurements. Dirt (e.g. dust, fingerprints, etc.) and damage impair the function.

► During assembly and maintenance work on high or ultra high vacuum systems, always wear 

clean, lint-free and powder-free laboratory gloves.

► Only use clean tools.
► Make sure that the connection flanges are free of grease.
► Remove protective caps and protective covers from flanges and connections only when necessa-

ry.

► Remove the analyzer’s transport protection only when necessary.
► Carry out all work in a well lit area.

Installation 

29/86

Содержание PrismaPro QMA 250 F1

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды