manualshive.com logo in svg

Pfeiffer Vacuum PrismaPro QMA 250 F1, Перевод оригинала

Поделиться
Скачать
Pfeiffer Vacuum PrismaPro QMA 250 F1 Скачать руководство пользователя страница 14

Risks during maintenance

 DANGER

Danger to life due to electric voltage

High voltages are present inside the device. When touching parts that are live, there is a risk of 
death. If there is visible damage, there is a risk of death when commissioning the device.

► Work on the open device must only be carried out by trained specialist personnel.
► Before carrying out any installation and maintenance work, switch the device off and disconnect 

it from the current supply.

– After switching off, wait about 60 seconds and then disconnect all cables (power cable at the 

end).

► Never open the device with the current supply connected.
► Secure the current supply against unauthorized or unintentional reactivation.
► Do not insert any objects into the vent openings.
► Never open an external power supply pack.
► Never operate an open or defective device.
► Secure a defective device against accidental operation.
► Protect the device against moisture.

 WARNING

Health hazard through poisoning from toxic contaminated components or devices

Toxic process media result in contamination of devices or parts of them. During maintenance work, 
there is a risk to health from contact with these poisonous substances. Illegal disposal of toxic sub-
stances causes environmental damage.

► Take suitable safety precautions and prevent health hazards or environmental pollution by toxic 

process media.

► Decontaminate affected parts before carrying out maintenance work.
► Wear protective equipment.

 WARNING

Risk of burns during baking out

During or immediately after the baking out, the heating jacket and the metal surfaces near to the 
heating jacket are extremely hot. The metal surfaces can reach a temperature of over 100 °C. This 
causes burns if you do not wear suitable personal protective equipment.

► When baking out, always wear personal protective equipment (for example protective gloves).
► Never touch surfaces without suitable protective gloves, either during or directly after baking out.

Risks when shipping

 WARNING

Risk of poisoning from contaminated products

Where products that contain harmful substances are shipped for maintenance or repair purposes, the 
health and safety of service personnel is at risk.

► Comply with the instructions for safe distribution.

Safety

14/86

Содержание PrismaPro QMA 250 F1

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды