Peter electronic VersiStart p III 105 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 108

background image

57

VersiStart p III

9.11 Inside Delta Operation

When connecting in inside delta, enter the motor full load current (FLC) for
parameter 1B. The VersiStart p III will automatically detect whether the motor is
connected in-line or inside delta and will calculate the correct inside delta current
level.

Adaptive Control, Jog, Brake and PowerThrough functions are not supported with
inside delta (six-wire) operation. If these functions are programmed when the
starter is connected inside delta the behaviour is as given below:

Adaptive Control Start

The starter performs a constant current start.

Adaptive Control Stop

The starter performs a TVR soft stop if parameter 2J

Stop Time

is >0 secs.

If parameter 2J is set to 0 secs the starter performs a
coast to stop.

Jog

The starter issues a warning with the error message
Unsupported option.

DC Brake

The starter performs a coast to stop.

Soft Brake

The starter performs a coast to stop.

PowerThrough

The starter trips with the error message Lx-Tx Shorted.

NOTE

When connected in inside delta, the VersiStart p III will not detect phase
loss on T2 during run.

9.12 Secondary Motor Set

The VersiStart p III can be programmed with two separate starting and stopping
profiles. This allows the soft starter to control the motor in two different starting and
stopping configurations.

This is ideal for situations where the motor may start in two different conditions
(such as loaded and unloaded conveyors).

The VersiStart p III will use the secondary motor settings to control a start when
instructed via a programmable input (refer to parameter 7A

Input A Function

and 7E

Input B Function

).

NOTE

VersiStart p III soft starters are not suitable for controlling two separate
motors. The secondary parameter set should only be used for a secondary
configuration of the primary motor.

«
...
56
57
58
59
60
...
»

Содержание VersiStart p III 105













































































































Отзывы:

Нет отзывов

Похожие инструкции для VersiStart p III 105

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Origami 4M-006-01

Бренд: 4 Moms Страницы: 28

Бренд: Bang & Olufsen Страницы: 36

Бренд: Mad Catz Страницы: 4

Бренд: Eaton Страницы: 6

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: V2 ELETTRONICA Страницы: 6

Бренд: Hach Страницы: 210

Бренд: hager Страницы: 62

coviva Smartbox TKP100A

Бренд: hager Страницы: 45

Бренд: Harsco Industrial Страницы: 57

Бренд: Veer Страницы: 2

Бренд: Jabra Страницы: 18

Бренд: U-Prox Страницы: 3

Бренд: PESA Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды