Peter electronic VersiStart p III 105 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 108

background image

VersiStart p III

46

9

Operation

9.1 Start, Stop and Reset Commands

The VersiStart p III can be started and stopped via the digital inputs, remote
keypad, communication network, smart card or scheduled auto-start/stop. The
command source can be set via the Setup Tools, or using parameter 1A

Command

Source

.

•

The VersiStart p III will only accept Start and Reset commands from the

designated command source.

•

The VersiStart p III will accept Stop commands from the designated

command source, but can be forced to stop by opening the reset input, or by
opening the start/stop input during an auto-start/stop cycle.

•

The programmable input can be used to override the selected command

source (refer to parameter 7A

Input A Function

).

9.2 Command Override

The programmable input (13, 14) can be used to override the command source, for
situations where the normal control mechanism has been lost. Set parameter 7A

Input A Function

to the alternative command source (eg 'Command Override:

Keypad').

While the input is active, the starter will only accept commands from the selected
override source. To restore control to the command source selected in parameter
1A

Command Source

, reopen the input.

9.3 Scheduled Start/Stop

The VersiStart p III can be configured to automatically start and/or stop the motor
once per day. For auto-start/stop to operate:

•

parameter 4A

Auto-Start/Stop Mode

must be set to 'Enable'

•

parameter 1A

Command Source

must be set to 'Clock'

•

the reset input must be closed

•

the start input (11, 12) must be active. This allows the VersiStart p III to be

stopped via the digital inputs in an emergency.

•

parameters 4B ~ 4V: Set as required.

9.4 PowerThrough

PowerThrough allows the soft starter to control the motor even if the soft starter is
damaged on one phase. The VersiStart p III will use two phase control techniques
to soft start and soft stop the motor. PowerThrough is only available with in-line
installations. If the starter is installed inside delta, PowerThrough will not operate.

NOTE

PowerThrough operation does not support adaptive control.

•

PowerThrough is only available with in-line installations. If the starter is

installed inside delta, PowerThrough will not operate.

•

PowerThrough remains active until '3-Phase Control Only' is reselected.

«
...
45
46
47
48
49
...
»

Содержание VersiStart p III 105













































































































Отзывы:

Нет отзывов

Похожие инструкции для VersiStart p III 105

Бренд: J4C Страницы: 4

Бренд: ABB Страницы: 6

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 168

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 29

Бренд: Panasonic Страницы: 37

Бренд: Panasonic Страницы: 9

Бренд: Hach Страницы: 36

Бренд: Hach Страницы: 72

Бренд: Mackie Страницы: 4

Бренд: Maclaren Страницы: 15

Бренд: Maclaren Страницы: 9

Бренд: Maclaren Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды