Peter electronic VersiStart p III 105 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 108

background image

5

VersiStart p III

2

Caution Statements

Caution Statements cannot cover every potential cause of equipment damage but
can highlight common causes of damage. It is the installer's responsibility to read
and understand all instructions in this manual prior to installing, operating or
maintaining the equipment, to follow good electrical practice including applying
appropriate personal protective equipment and to seek advice before operating this
equipment in a manner other than as described in this manual.

NOTE

The VersiStart p III soft starter is not user serviceable. The unit should only
be serviced by authorised service personnel. Unauthorised tampering with
the unit will void the product warranty.

2.1 Electrical shock risk

WARNING – ELECTRICAL SHOCK RISK

The voltages present in the following locations can cause severe electric
shock and may be lethal:

•

AC supply cables and connections

•

Output cables and connections

•

Many internal parts of the starter

The AC supply must be disconnected from the starter using an approved
isolation device before any cover is removed from the starter or before any
servicing work is performed.

SHORT CIRCUIT

The VersiStart p III is not short circuit proof. After severe overload or short
circuit, the operation of the VersiStart p III should be fully tested by an
authorised service agent.

GROUNDING AND BRANCH CIRCUIT PROTECTION

It is the responsibility of the user or person installing the VersiStart p III to
provide proper grounding and branch circuit protection according to local
electrical safety codes.

FOR YOUR SAFETY

§

The STOP function of the soft starter does not isolate dangerous

voltages from the output of the starter. The soft starter must be
disconnected by an approved electrical isolation device before accessing
electrical connections.

§

Soft starter protection features apply to motor protection only. It is the

user’s responsibility to ensure safety of personnel operating machinery.

§

The soft starter is a component designed for integration within an

electrical system; it is therefore the responsibility of the system
designer/user to ensure the system is safe and designed to comply with
relevant local safety standards.

«
...
4
5
6
7
8
...
»

Содержание VersiStart p III 105













































































































Отзывы:

Нет отзывов

Похожие инструкции для VersiStart p III 105

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: KELCO Страницы: 36

Бренд: B&R Industries Страницы: 89

Бренд: HABONIM Страницы: 9

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 50

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 39

Бренд: National Instruments Страницы: 22

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 20

Бренд: National Instruments Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды