Peter electronic VersiStart p III 105 Скачать руководство пользователя страница 37

Страница: 37 / 108

VersiStart p III

6.5 Load/Save Settings

Load/Save Settings allows users to:

•

Reset the VersiStart P III's parameters to default values

•

Load parameter settings from an internal file

•

Save the current parameter settings to an internal file

The internal file contains default values until a user file is saved.

To load or save parameter settings:

Press

MENU

to open the menu then select Setup Tools.

1. Scroll to Load/Save Settings and press the

ENTER/MENU

button.

2. Scroll to the required function and press the

ENTER/MENU

button.

Load/Save Settings

Load Defaults

Load User Set

Save User Set

3. At the confirmation prompt, select YES to confirm or

NO to cancel, then press

ENTER/MENU

to proceed.

Load Defaults

Yes

When the action has been completed, the screen will briefly display a
confirmation message, then return to the previous menu level.

6.6 USB Save & Load

The USB Save & Load menu lets you:

•

Save parameter settings and all event log entries to an external file (CSV

format)

•

Save parameter settings to an external file (proprietary format)

•

Load parameter settings from a previously saved external file

•

Load custom messages to display on the keypad when a programmable

input is active

NOTE

VersiStart P supports FAT32 file systems. VersiStart P USB functions are
not compatible with NTFS file systems.

Save & Load Procedure

1. Connect the external drive to the USB port.

2. Press

MENU

to open the menu then select Setup Tools.

3. Scroll to USB Save & Load and press the

ENTER/MENU

button.

4. Scroll to the required function and press the

ENTER/MENU

button.

USB Save & Load

Save Params and Logs

Save Master Params

Load Master Params

5. At the confirmation prompt, select YES to confirm or

NO to cancel, then press

ENTER/MENU

to proceed.

Save Params and Logs

Yes

When the action has been completed, the screen will briefly display a
confirmation message, then return to the previous menu level.

Содержание VersiStart p III 105













































































































Результаты поиска

Содержание VersiStart p III 105

Отзывы:

Бренды по названию

Популярные бренды

Peter electronic VersiStart p III 105, Инструкции по сборке и пусконаладке

Результаты поиска

Содержание VersiStart p III 105

Отзывы:

Бренды по названию

Популярные бренды