13. Alarm
14. Settings
#
#
#
#
#
!
#
#
Upon detection, a detector will send an alarm signal to the siren.
If the system is armed, the panel will give an acoustic warning for the set
alarm period (factory default 3 minutes). If the detector was set to
delay, then the alarm will be delayed accordingly.
Each telephone number stored in SMS 6 will be sent an SMS.
Then the first telephone number stored in SMS 5 will be called. If the call
is not answered the next number will be called etc. When a call is
answered the acoustic signal from the panel will stop and the called
party can listen in to through the panel microphone. In this case the
following numbers will not be called.
The alarm is indicated visually on the panel through the flashing of the
numerical key [6] corresponding to the alarmed detector (0= panic
alarm, 1 to 9= detector 1-9). This indication is cancelled when the
system is disarmed.
To stop the alarm disarm the system. If the system is disarmed using an
RFID tag the number stored with SMS 7 is sent an SMS.
If the alarm is not cancelled the system remains armed after the alarm period
Note that in operating mode a PIR-detector will be deactivated for 3-5
minutes after each detection) that means that the PIR only sends a
signal to the siren after it has
registered movement for a period of 3
to 5 minutes.
During disarmed status the system monitors the detectors. If a battery
compartment lid is removed, eg. a from contact is removed from the
door frame, then the detector sends tamper alarm signal to the panel.
The panel sounds an acoustic warning for the set alarm period and sends
an SMS to the first number stored with SMS 6.
The system is factory set as follows:
delay for delayed detectors
30 seconds
delay for other detectors
0 seconds (=immediate alarm)
volume of panel siren
2 (normal)
alarm period
3 minutes
user code
1 2 3 4
language
German*
key tone
activated
* to change the language see chapter 12
Settings can be changed and set only by sending SMS commands from the
numbers stored with SMS "5" and “6” to the number of SIM card in the
panel. The SMS commands can also be send using the Application.
00
status enquiry
status and settings sent by SMS
?
Enquiry menu 1
first menu side sent by SMS (SMS 0 /
1 / 2 / 3 / 4 / 00 / ??)
??
Enquiry menu 2
second menu side sent by SMS
(SMS 5/6/7/8/???)
???
Enquiry menu 3
third menu side sent by SMS
(SMS 91-99/101- 104 / 11 / 12 / 13
not
SMS text
command
reaction
/ 14)
5*
store numbers
per SMS enter max. 5 numbers for
for setting /
setting and for receiving alarm calls
and alarm calls
6*
store numbers
per SMS enter max. 5numbers for
for setting /
setting and for receiving alarm SMS
for alarm SMS
(no. Stored as “1." will be sent SMS
upon mains power failure and tamper
alarm)
7*
store number
per SMS enter 1 number which
to receive SMS
receives SMS for disarm with RFID
for RFID disarm
tag**
8*
Preset number
per SMS enter 1 preset number
91-99*
name detectors
per SMS name detectors 1 to 9
1-9
(for detectors 10 to 50 the text
remains: detector X Alarm)
101-104*
SMS text
per SMS enter SMS text (max. 30
for RFID disarm
tokens), to be sent when disarming
with the first 4 enrolled RFID tags**
11*
delay for other
per SMS enter the entry/exit delay
detectors
(0 to 300 seconds - usually leave as
factory default=0)
12*
volume and
per SMS enter values
period of alarm
(volume: 0 = off, 1 = quiet, 2=
normal; period: 1 to 9 minutes)
13*
change user code
per SMS enter new user code
14*
delay for delayed
per SMS enter delay
detectors
(0 to 300 seconds, 0= no delay)
21
delete all wireless
per SMS delete all detectors and
components
remote controls
22
delete all RFID tags
all RFID tags will be deleted
30
deactivate key tones per SMS deactivate the key tones
31
activate key tones
per SMS activate the key tones
0000
Reset
all settings back to factory default ***
0001
English
per SMS set the SMS language to
English
* for all commands marked * the SMS received from the panel must be
edited and then
to the panel, in order to store the
changes/settings. The successful change/setting will be confirmed by
SMS.
Do not use spaces while editing and forwarding the SMS.
1. Send an SMS with text "12" to the panel.
2. Panel answers with following SMS:
forwarded
Note:
Example: set alarm volume and period
Siren volume (0 Mute, 1 Low,
2 High)
2
Siren ringing
time (1-9min):
3
42
