#
#
#
#
#
#
#
#
#
#
#
!
#
#
#
Walls and floors, especially those containing metal, metalised foil,
reinforced concete or stone
Coated windows (eg. Energy saving windows), radiators, refridgerators,
mirrors, metalic surfaces or doors
Electrical wiring and electrical appliances (eg. motors, microwave
ovens)
Devices using the same or similar wireless frequency.
short wireless range antenne is covered
do not cover the front of the
of remote control
remote control
Alarm without
PIR-detector reacts check positioning of PIR,
apparent reason
to temperature
do not point towards heat
differences
sorces
PIR-detector does
In operating mode
Wait, or press the test
not react
deactivated for up
button (23). After the
to 5 minutes after
deactivation period the
each detection
unit will detect immediately
siren no longer reacts detector or remote
reset the siren and enroll all
to detector or
control is no longer components
remote control
enrolled; e.g.
jumper position
has been changed
Regularly check the technical safety and function
Before you clean the device, pull the mains adapter out of the mains
socket and remove the batteries.
Use a soft, dry or slightly moist cloth or a dry brush for cleaning the
surfaces.
3000M, Door/window contact, Art.Nr.33531
3000R, Remote control, Art.Nr. 33532
3000P, PIR-detector, Art.Nr. 33530
3000 Set F4, GSM-wireless alarm system, Art.Nr. 33523
Use ear protection
Use a ball point pen to press the connect button (6) on the siren. The
siren beeps and the LED (3) lichts yellow/orange for 10 seconds. Within
this period you can enroll one of the following components:
Remote control: press the disarm button (12) once
PIR-detector: press the test button (23) twice
door/window contact: trigger by separating magnet from the sensor
The enrollment will be confirmed by the siren with a beep and LED (3)
will flash.
16. Troubleshooting
17. Maint cleaning
18. Optional accessories
19. Enrolling further components to the siren
Fault
Cause
Remedy
20. Delete all components (Reset)
21. Disposal
22. Declaration of conformity
23. Warranty
If a remote control is lost, delete all components and then enroll the
remaining components again (see chapter 19), to maintain the security of
the system.
To delete all remote controls and detectors hold the connect button (6)
on the siren with a ball point pen pressed until the deletion is confirmed
by a beep and flash.
Enroll a remote control as the first item, by pressing the disarm button (12)
2 times, then you can cancel an unwanted alarm.
Packaging material, used batteries or electrical products must not be
disposed of as household waste. Use your recycling system. Details
are available from your local authority.
INDEXA GmbH, Paul-Böhringer-Str. 3, D - 74229 Oedheim, hereby declares
that the 3000 Set F3 is in compliance with the essential requirements and
other relevant provisions of Directive 1995/5/EC. The original of the
conformity assessment can be found on the web site www.pentatech.de.
In addition to the statutory guarantee from the vendor, the manufacturer
warrants this product for 2 years from date of purchase (proof from receipt)
according to following conditions.This warranty does not affect your legal
rights. The warranty covers use of the product in normal conditions in private
households. It only covers manufacturing defects and is limited to the
replacement or repair of the faulty components. It does not include wear and
tear, or batteries. The warranty applies only when the product is used
according to the operating instructions. It does not cover damage arising
from misuse, improper handling, application of force, dust, dirt, water or
other environmental factors, or from incorrect voltage from batteries or power
supply.
The warranty is void when the product has been repaired or tampered by
unauthorised persons and when it has been used with components which are
not specified by the manufacturer. In case of a warranty claim please contact
the vendor for details of how to proceed and how to return the product if
necessary. Only carriage paid authorised returns will be accepted. Repairs
can only be accepted when accompanied by a full description of the fault.
After the warranty period has expired repairs will be charged and are not
always possible. Warranty claims do not extend the warranty period and the
warranty for replacement parts expires with the warranty for the product.
Unless there is a statutory obligation, the manufacturer is not responsible for
further claims, including peronal or material damages, arising from the use
of the product or from nonfunction or misfunction of the product.
!
Tip:
31
