15
Installation and User’s Guide
Connecting the Heat Pump Control Board to IntelliTouch
®
or
EasyTouch
®
(
Continued
)
Pin Configuration for the Heat Pump Control Board to IntelliTouch
®
:
•
Heat Pump Control Board: Connect pin 2 (green) to IntelliTouch
®
screw terminal pin 2 (green)
•
Heat Pump Control Board: Connect pin 3 (yellow) to IntelliTouch
®
screw terminal pin 3 (yellow)
IMPORTANT
—
Do NOT use pin 1 (black) or pin 4 (red) on the AutoSet board or the IntelliTouch
®
mother board.
6. Close the IntelliTouch
®
control panel and secure it with the two access screws.
7. Install the high voltage panel cover and secure it with the two retaining screws.
8. Close the load center front door and secure with the two latches.
9. Switch power on to the IntelliTouch
®
load center.
Connecting the IntelliTouch
®
or EasyTouch
®
to Heat Pump
1. Turn off the power to both the remote pool/spa control system and the heat pump.
2. Remove the front left panel of the heat pump cabinet,
(you do not need to remove the torque head screw
at the top left corner).
3. Remove the electrical service panel to the heat pump. Remove the 4 bezel retaining screws from above the
electrical compartment and rotate the bezel downward. This will allow you to access the Remote terminals on
the back of the Heat Pump control board for the remote control installation.
4. Run the wires from the pool/spa remote control system into the upper electrical compartment.
5. Connect the wiring from the IntelliTouch
®
Personality Board COM PORT to the RS-485 IntelliTouch
®
connection (J8) on the Heat Pump control Board. Connect the Green wire to J8 pin 2 and yellow wire to J8
pin 3. Do NOT use pin 1 (red) or pin 4 (black) wires. The connections are shown in the
Figure 15
.
6. Rotate the bezel back upwards into position and reinstall the 4 retaining screws
7. Replace the electrical service panel.
8. Replace the front left panel.
9. Restore power to the heat pump and the pool/spa remote control system.
10. Press the Menu Select button to scroll to the Serial Remote screen. Toggle the selection
by pressing one of the arrows until the screen displays “Serial Remote On”.
PIN CONFIGURATION
IntelliTouch
COM PORT (J7/J8)
screw terminal
IntelliTouch
screw terminal
connector
AutoSet Board
(4-wire cable)
2 (GRN)
3 (YEL)
GREEN (PIN 2)
YELLOW (PIN 3)
Figure 15.
IntelliTouch Personality
Board COM PORT
(J7/J8)
COMMUNICATION PORT
Pin Configuration for connecting IntelliFlo
®
to IntelliTouch
®
:
Strip back the cable conductors 1/4”. Insert the two wires into either of the
COM PORTS
(
J7
and
J8
) screw terminals. Secure the wires with the screws.
Note:
Multiple wires may be inserted into a single screw terminal.
A communication expansion module with 3 extra COM ports and 4 IntelliFlo
pump ports is available (P/N 520818).
• IntelliFlo: Connect pin 6 (green) to IntelliTouch screw terminal pin 2 (green)
• IntelliFlo: Connect pin 7 (yellow) to IntelliTouch screw terminal pin 3 (yellow)
IntelliTouch
Screw Terminal
COM PORT (J7 / J8)
1
2
3
4
BLK
GRN
YEL
RED
INDOOR CONTROL
(AND/OR)
RF TRANSCEIVER
(AND/OR)
iS10
SPA-SIDE REMOTE.
Figure 14.
24 VAC
CO
MP
RE
SS
OR
FA
N
LO
W
PR
ES
HI
PR
ES
RE
VE
RS
IN
G
VA
LV
E
FL
OW
Heat Pump Control Board
PU
MP
THERM1
THERM2
COM
SPA
POOL
INPUT
SWITCHES
J9
WTR
TEMP
J4
DEF
TEMP
J5
3 - WIRE
REMOTE
TERM.
PWR
J7
OUTPUTS
J3
J8 RS-485
INTELLITOUCH
CONNECTION
PIN 2
(Green)
PIN 3
(Yellow)
Содержание ThermalFLo HP
Страница 54: ...46 Installation and User s Guide SAVE THESE INSTRUCTIONS...
Страница 55: ...47 Installation and User s Guide NOTES...
Страница 56: ...P N 474099 Rev C 08 02 10 474099...