Pentair IntelliFlo VS+SVRS Скачать руководство пользователя

Страница: 10 / 56

INTELLIFLO

VS+SVRS and INTELLIPRO

VS+SVRS Variable Speed Pump Installation and User’s Guide

Motor Assembly

The IntelliFlo

VS+SVRS Pump’s three-phase six-pole motor operates from 3450 RPM to 1100

RPM. The drive assembly is continually cooled by an external fan. Dual seals on the motor drive

shaft and at the fan shaft assembly seal the entire motor and bearings from any dirt and moisture

entering the motor assembly. For added protection, a slinger located in front of the main motor shaft

seal assists in slinging water away from the shaft opening in the flange.

Drive assembly and
electronics enclosure

Pump Assembly

Motor fan cover

Communication port for connection

to EasyTouch

, IntelliTouch

SunTouch

Control System or

IntelliComm

Communication Center

via two-wire RS-485 cable

Motor assembly

Control panel cover

Motor Features

• Permanent Magnet Synchronous Motor (PMSM)

• High efficiency

• Superior speed control

• Operates at lower temperatures due to high efficiency

• Same technology as deployed in hybrid electric vehicles

• Designed to withstand outdoor environment

• Totally enclosed fan cooled

• Three-phase motor

• 56 Square Flange

• Six-Pole

• Low noise

Содержание IntelliFlo VS+SVRS

























































Результаты поиска

Содержание IntelliFlo VS+SVRS

Отзывы:

Похожие инструкции для IntelliFlo VS+SVRS

Бренды по названию

Популярные бренды

Pentair IntelliFlo VS+SVRS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание IntelliFlo VS+SVRS

Отзывы:

Похожие инструкции для IntelliFlo VS+SVRS

Бренды по названию

Популярные бренды