Pentair FLECK 9000 SXT Скачать руководство пользователя

Страница: 94 / 118

Installer manual Fleck 9000 SXT - Maintenance

94 / 118

Ref. MKT-IM-020 / C - 21.11.2019

9.4.11

Valve on tank assembly

1. Lubricate the seals with approved silicone grease.

2. Spin the valve (

) onto the tank (

), ensuring the threads are not cross-threaded.

3. Rotate the valve (

) clockwise and freely, without using force until it comes to a stop.

Info

This stop position is considered point zero.

4. Rotate the valve (

) clockwise from point zero to between ¼ turn and ½ turn.

Caution - material

Risk of damage due to excessive force !

Do NOT exceed 27 Nm of torque when installing the valve. Exceeding this limit may
damage the threads and cause failure.

Point 0

½ turn

Point 0

¼ turn

Point 0

½ turn

Point 0

¼ turn

Содержание FLECK 9000 SXT























































































































Результаты поиска

Содержание FLECK 9000 SXT

Отзывы:

Похожие инструкции для FLECK 9000 SXT

Бренды по названию

Популярные бренды

Pentair FLECK 9000 SXT, Руководство по установке

Результаты поиска

Содержание FLECK 9000 SXT

Отзывы:

Похожие инструкции для FLECK 9000 SXT

Бренды по названию

Популярные бренды