Pella Insynctive Lifestyle Series Скачать руководство пользователя

Страница: 14 / 16

Pella

Lifestyle Series Motorized, Integrated Blinds and Shades with Insynctive | 14

Inductive Charging Instructions

GETTING STARTED

If your Pella Insynctive Motorized Blinds or Shades have been working just fine up

until recently and then quit working, they likely need to be charged with the Insynctive

Inductive Charger.

NOTE: Ensure you are using the supplied wall adapter with the Inductive Charger to

ensure safe and proper operation of the Inductive Charger. Failure to do so could

result in injury, damage to product and property, and void any warranty of Insynctive

products.

Locating the Inductive Charger Receiver

On the other end of the inductive charger is the receiver (not visible), located inside

the battery pack. In order for the charger to work properly, the transmitter and

receiver must be properly aligned.

To find the location of the receiver located inside your Pella Lifestyle Series product,

place the transmitter on the glass, along the bottom edge of the unit, with the wire on

the transmitter pointing in towards the center of the unit.

• If on the correct side, the transmitter will magnetically connect to the receiver,

LED will turn BLUE.

• If the transmitter does not magnetically connect to the receiver, place the

transmitter on the other side of the unit.

Using the Charger
1. Connect transmitter with the AC adapter and plug in

• When you plug in the 12V wall adapter to the transmitter, the LED on the

transmitter should turn GREEN. This indicates that there is power to the

transmitter, and the correct power source is being used.

• If the wrong wall adapter is used, or there is an issue with the power source

itself, the LED on the transmitter will blink RED (pattern: Blink, Blink, Stop; Blink,

Blink Stop; etc…)

• The transmitter requires a 12VDC power source. Only use the wall adapter

provided to you with charger kit purchased from Pella.

• If you are using the provided power source, and still have a blinking RED LED,

call Customer Service at 855-473-5524.

2. Place transmitter on the window unit

• When the transmitter has been properly placed on the receiver, the LED on

the transmitter will turn BLUE. The BLUE LED indicates the inductive charger is

charging the battery pack. It will remain blue until the battery is fully charged, at

which time it will turn Green (approx. 8 hours for full charge).

3. Remove transmitter once charging is complete

Close up of specifications

on the 12V wall adapter

Inductive transmitter paired with receiver

located on casement unit, with wire facing interior.

If needed the suction cup included can help keep

some of the cord weight off of the charger.

Shown is the 12V wall adapter cord, Inductive

Charger Transmitter, and suction cup, all

included in the charging kit.

Inductive Transmitter paired with Receiver

located on Casement Unit

Wire facing interior

Содержание Insynctive Lifestyle Series

















Результаты поиска

Содержание Insynctive Lifestyle Series

Отзывы:

Похожие инструкции для Insynctive Lifestyle Series

Бренды по названию

Популярные бренды

Pella Insynctive Lifestyle Series, Руководство по эксплуатации продукта

Результаты поиска

Содержание Insynctive Lifestyle Series

Отзывы:

Похожие инструкции для Insynctive Lifestyle Series

Бренды по названию

Популярные бренды