Parkside PBKS 53 A1, Руководство по эксплуатации и технике безопасности

Страница: 28 / 176

23 GB/IE
2. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-
cians,
• Installation and replacement of non-original spare parts,
• Application other than specified.
We recommend:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt and
moisture. Read the instruction manual each time before operat-
ing the machine and carefully follow its information.
The machine can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety instructions contained in this operating
manual and the specific regulations of your country, the techni-
cal rules generally accepted for the operation of machines of
the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.
3. Device description (fig. A - O)
1. Front hand guard
2. Front handle
3. Air filter cover
4. Starter pull cord
5. Cap for the air filter cover
6. On/Off switch
7. Fuel pump (primer)
8. Cold start lever (choke)
9. Throttle control lock
10. Throttle control
11. Rear handle
12. Rear hand guard
13. Fuel tank cap
14. Chain oil tank cap
15. Spiked bumper (pre-assembled)
16. Guide rail (pre-assembled)
17. Saw chain (pre-assembled)
18. Grinder support
19. Oil adjusting screw
20. Locking nut
21. Chain-tensioner screw
22. Sprocket cover
23. Chain tensioner pin
24. Chain catcher
25. Hole for the chain tensioner pin
26. Chain sprocket
27. Guide rail cover
28. Ear muffs EY2-1
29. Safety goggles GF08
30. Mixing container
31. Spark plug wrench/flat-blade screwdriver
32. Organic chain oil
33. Air filter
34. Spark plug connector
35. Felling marks
4. Scope of delivery
• 1 Chain Saw (pre-assembled)
• 1 spark plug wrench/flat-blade screwdriver
• 1 cover for the guide rail (chain guard)
• 1 mixing container
• 500 ml organic chain oil (Made in Germany)
• 1 pair of safety goggles GF08
• 1 set of ear muffs EY2-1
• 1 set of operating instructions
5. Intended use
The chainsaw is only for sawing lumber outdoors. The chain-
saw may not be used for other purposes.
Do not make any modifications to the chainsaw. This can
compromise safety. The user/operator is liable for any result-
ing damage or injuries of any kind and not the manufacturer.
Please note that this appliance is not designed for commercial
use according to its intended purpose.
We accept no warranty liability if the appliance is used in com-
mercial, manual trade or industrial operations or equivalent
activities.