background image

43

42

USER MANUAL

PANDORA DXL 1940L CAR SERVICE-SECURITY SYSTEM

Meaning of indicator LED colors

Indicator status

Meaning

Short red flashes

The system is armed

Lit red

The system is preparing for automatic arming

Orange flash

Confirms VALET button press

Green flashes

Confirms a number of recorded remotes (when switching on 
ignition)

Red flash

Confirms a recorded mobile device (when switching on ignition)

Red and green flashes

PIN-code confirmed

Faded

The system is disarmed

Checking the number of registered radio tags/mobile devices

The number of recorded tags and mobile device can be checked by the number of green and red 

flashes of LED indicator. Number of registered tags can be checked every time the ignition is switched 
on when the system is disarmed. Number of green LED flashes will indicate the number of recorded 
tags, following red flash will indicate registered mobile device.

You can also check the number of recorded tags and registered mobile device by taking off and put-

ting back on battery terminal. The system will emit short sound signals from a siren with less than 1 sec. 
interval. The number of the signals equals to the number of recorded tags. After a pause of 2 seconds 
the system signal will indicate registered mobile device.

System modules layout

Ask the installer to mark system’s modules on the picture provided. This information can be important 
for diagnostics in case system malfunctions.

Base unit

Valet button

Blocking radio relay

LED indicator

Automatic start module

GPS-receiver

1

2

3

4

5

6

Содержание DXL 1940L


























Отзывы: