29
28
USER MANUAL
PANDORA DXL 1940L CAR SERVICE-SECURITY SYSTEM
• Wire «11» (Orange-black) (CAN1-Low)
— It connects to appropriate CAN-Low wire of the car.
• Wire «12» (Yellow-black) (CAN2-Low)
— It connects to appropriate CAN2-Low wire of the car.
• Wire «13» (Blue-Black) (CH3)
—Factory setting is ‘Blocking N.O.’. This output is used to control
blocking relay with a normally open logic (it becomes grounded on switching on the ignition when the
system is disarmed; when a radio tag is in the coverage zone if the Immobilizer/Anti-Hi-Jack function is
enabled). A negative output of additional channel with maximum load current 200mA. This output is
multipurpose, it can operate in accordance with selected logic.
• Wire «14» (Yellow) (INP2)
— Factory setting is ‘Ignition’. This wire connects to ignition switch or to
appropriate wire where 12V voltage appears when ignition is switched on. This input is multipurpose, it
can operate in accordance with selected logic.
• Wire «15» (Purple) (СН11)
— Factory setting is “Siren” It connects to the siren control wire (+) (maxi-
mum load current is 2A). This output is multipurpose, it can operate in accordance with selected logic.
• Wire «16» (Red) (Power 12V)
— It should be connected to reliable conductor with con-
stant voltage of 12V.
Х6 Socket (Relay module):
• Wire «1» (Blue) (CH6)
— Factory setting is ‘Blocking N.O.’. This output is used to control blocking
relay with a normally open logic (it becomes grounded on switching on the ignition when the system is
disarmed; when a radio tag is in the coverage zone if the Immobilizer/Anti-Hi-Jack function is enabled).
An output of additional channel with maximum load current 250mA. This output is multiputpose, it can
operate in acordance with selected logic as a negative or positive output (it depends on the settings).
• Wire «2» (Orange) (CH7)
— Factory setting is ‘ACC’. The channel is used to control accessories
through an external relay. If ‘Car with START/STOP button’ setting is enabled, the channel will control
brake pedal during remote or automatic engine start. An output of additional channel with maximum
load current 250mA. This output is multiputpose, it can operate in acordance with selected logic as a
negative or positive output (it depends on the settings).
• Wire «3» (Brown) (CH8)
— Factory setting is ‘Ignition’. This output is used to switch on the ignition
through an external relay. It allows implementing automatic engine start, turbo timer, ignition support
and connecting to ignition in series (incut). If ‘Car with START/STOP button’ setting is enabled, the channel
will operate in impulse mode to control the button. A negative output of additional channel with maxi-
mum load current 200mA. This output is multipurpose, it can operate in accordance with selected logic.
• Wire «4» (Green) (CH9)
— Factory setting is ‘Bypass’. Output activates during remote or automatic
engine start. A negative output of additional channel with maximum load current 200mA. This output
is multipurpose, it can operate in accordance with selected logic.
• Wire «5» (Yellow) (CH10)
— Factory setting is ‘Starter’. This output is used to switch on the starter
of a car through an external relay. A negative output of additional channel with maximum load capacity
200mA. This output is multipurpose, it can operate in accordance with selected logic.
• Wire «6» (Red)
— relay module power supply 12V.
Х4 Socket (Multifunctional channels)
Use this socket when implementing bypass of original immobilizer using IMMO-KEY1 and IMMO-KEY2
multifunctional channels. Make connections in accordance with installation scheme. The settings of the
socket are available in AlarmStudio. Disconnect the system from power supply after changing the settings.
Programming the system
Entering programming menu
To change the system settings or program the system using a computer or
VALET
button, the sys-
tem should be in programming mode. Enter programming mode by entering ‘
Service PIN-code’
(fac-
tory preset is 1-1-1-1). PIN-code should be entered using external or located on the base unit
VALET
button. The input is indicated by flashes of external or located on the base unit LED indicator. You can
enter the code only if the base unit is powered form USB socket or from external power supply, the igni-
tion is switched off, the system is disarmed and maintenance mode is switched off.
If there is no
‘Service PIN-code’,
you can enter programming mode using the ‘
Secret PIN-code’
written on the owner’s card.
Entering PIN-code:
•
Enter the first digit of the code using
VALET
button. Press the button a number of times, equals to
the first digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed with
an orange LED indicator flash. A pause for more than 1 second and a red LED indicator flash confirm the
input of the first digit. Then you can enter the next digit.
