31
30
USER MANUAL
PANDORA DXL 1940L CAR SERVICE-SECURITY SYSTEM
• Enter the second digit of the code using
VALET
button. Press the button a number of times,
equals to the second digit. Pauses between presses should not exceed 1 second. Each pressing will be
confirmed with an orange LED indicator flash. A Pause for more than 1 second and a red LED indicator
flash confirm the input of the second digit. Then you can enter the next digit.
• Enter the third digit of the code using
VALET
button. Press the button a number of times, equals
to the third digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed
with an orange LED indicator flash. A Pause for more than 1 second and a red LED indicator flash confirm
the input of the third digit. Then you can enter the next digit.
• Enter the fourth digit of the code using
VALET
button. Press the button a number of times, equals to
the fourth digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed with an
orange LED indicator flash. The system will confirm correct PIN-code with the series of red and green flashes
and the system will enter programming mode. If the input was incorrect, it will be indicated with a red LED
indicator flash and the system will stay in a previous state. New input can be attempted after 5 seconds.
Exit programming mode:
To exit programming mode turn on the ignition or turn off power of the base unit. The system will reboot
programmatically (all changes will be saved) after exiting programming mode using ignition. All ways to exit
the programming menu are accompanied by sound signals of the siren/Beeper and light signals of the LED
indicator. Light signals indicate the number of recorded devices: first green flashes indicate the number of
recorded radio tags, red flash indicates registered mobile device
Status indicator lights during PIN-code entering:
Short orange flash
Confirmation of VALET button pressing
Short red flash
Confirmation of entering a PIN-code digit
Red and green flashes
PIN-code is correct
Long red flash
PIN-code is incorrect
Preparing to program the system using a computer
The system allows programming all settings and updating software of the base unit via micro-USB ca-
ble. If the base unit has not been installed in the vehicle yet, it will be powered via micro-USB cable while
programming. To program using a computer, you need a standard USB cable, a computer with Windows XP/
Vista/7/8/10 and
Pandora Alarm Studio
application (you can download it from
pandorainfo.com
).
It is required to create an account in AlarmStudio to use
Pandora CLONE
for remote engine start (you
can register without a connection to a system).
Pandora CLONE
procedure requires Internet connection.
In preparation to the programming these stages should be followed:
•
connect the system and PC via USB cable;
• start Pandora Alarm Studio;
• enter the programming settings mode by entering the service PIN-code.
Updating firmware
It is recommended to update firmware of the base unit before installing and programming the system
(actual vesion of the firmware you can download from
pandorainfo.com
). You can update firmware using
AlarmStudio
application after entering programming mode or using quick boot algorithm (PIN-code is not
required).
Quick boot mode: open
AlarmStudio
; de-energize and disconnect the system; press and hold
VALET
button located on the base unit; release the button immediately after connecting the system and a computer
via USB cable; the system will enter boot mode.
If the boot mode has been interrupted for some reason and the status indicator lights red, you need to
load firmware using quick boot mode (without entering PIN-code).
Level 1
Recording radio tags into the system’s memory (BT760)
Level 2
Changing the factory preset of the service PIN-code
Level 3
Recording the idle speed to the system memory
Level 4
Resetting to factory settings
Level 5
Recording Bluetooth engine compartment module (RHM-03 BT)
Level 6, 7
Recording Bluetooth radio relays №1, №2 (BTR-101)
Level 8
Recording Bluetooth GPS/GLONASS receiver (NAV-035 BT)
Level 10
Configuring system settings via the wireless interface
Level 11
Programming and configuring ‘Immobilizer PIN code’
Level 15
Emergency disabling of immobilizer radio tag
