37
36
USER MANUAL
PANDORA DXL 1940L CAR SERVICE-SECURITY SYSTEM
with orange flashes. If there are no orange flashes when any button is pressed, then this button is not
recognized by the system, select a different button. Repeat the procedure to select the second, third,
fourth button and enter the next sublevel. To enter the next sublevel 11.2l press VALET button once.
Sublevel 11.2 - Entering PIN-code:
Program immobilizer deactivation PIN-code using selected button or buttons. Enter the first digit
by pressing the previously selected button (pauses between presses should not exceed 1 second). The
base unit will confirm entering with red flash of LED indicator. Enter the second (third, fourth) digit by
pressing the previously selected button. The base unit will confirm entering of each digit with red flash
of LED indicator.
Input the required number of digits (up to 4) and then press
VALET
button. The system will confirm
receiving of the secret validator code with long red flash of
LED
indicator and will wait for confirmation
of
PIN-code
.
Sublevel 11.3 - Confirmation of the PIN-code input:
11.2 Enter PIN-code
again similarly to the procedure (level 11.2 – Entering PIN-code) and press
VALET button. The system will confirm correct PIN-code with red and green flashes of LED indicator and
will memorize PIN-code, and then the system will proceed to programming mode awaiting level input.
Incorrect confirmation is indicated with long red flash of LED indicator, after that the system will return
to programming mode.
Level 15 – Disabling/enabling immobilizer tag
To disabling/enabling of immobilizer tag, enter programming menu and press
VALET
button 15
times. LED indicator will light green (green light indicates enabled tag) and the system will wait for the
“
Secret PIN-code
” entering. Red light of LED indicates disabled immobilizer tag.
Disabling radio tag:
LED indicator will light green after entering the programming level. The system will wait for entering
the
‘Secret PIN-code’
. Enter the ‘Secret PIN-code’ that is written on the owner’s plastic card. The system
will confirm disabling of the radio tag with two sound signals of the siren and a long red LED flash. After
that the system will return to the programming menu. If the PIN-code is not entered within 10 seconds
or the input is incorrect, a siren will sound one signal, LED will produce the series of red and green
flashes and the system will return to the programming menu.
Enabling radio tag:
LED indicator will light red after entering the programming level. The system will wait for action.
Press
VALET
button once to enable radio tag. The system will confirm enabling with one short sound
signal of a siren and a green LED light. After that the system will return to the programming menu.
Level 16 – Updating built-in Bluetooth modem firmware
Download the firmware from www.pandorainfo.com and install Pandora BT application on your
mobile device (Android version 4.4 or high or iOS version 9.3.5 and higher) with Bluetooth 4.0
Low Energy or higher support).
To update firmware of the built-in Bluetooth modem, enter programming mode and press
VALET
button 16 times. Find your system in the mobile application, go to detected devices and select one of
the updating option:
File manager
(for Android only) or
Internet
and update Bluetooth modem firm-
ware. File manager allows to upload the firmware from the phone storage and Internet option allows to
upload Firmware from the server to the base unit.
Level 17 – Programming bypass of original immobilizer
Bypass learning procedure is performed on this level. A detailed manual can be found in installa-
tion scheme for a car in AlarmStudio.
Enter programming mode and press
VALET
button 17 times. LED indicator will be lit green. If system in-
stallation was performed correctly on successful engine start using a key, LED indicator will flash green.
After completing of the procedure, a siren will emit a short sound signal and LED indicator will light
green. If the learning procedure finishes with an error, LED indicator will light red.
Saving changes:
To finish the learning procedure, switch on the ignition and press
VALET
button. The system will
return to programming mode.
Level 18 – Pairing and unpairing mobile device
The system supports only one mobile device. Pairing of a new mobile device (if the system has previ-
ously paired device) is not allowed without unpairing procedure. When you overwrite the same device
in the system memory, you should delete the Bluetooth connection on your mobile device, delete the
mobile device from the system memory and then pair the mobile device in the system memory.
To pair a mobile device, enter the programming mode and press
VALET
button 18 times. LED indi-
cator will light green (green light indicates the system is ready to pair a mobile device) and the system
will enter the mobile device pairing mode. Red light of LED indicates the system has already had regis-
tered mobile device, overwriting of mobile device can be done only after unpairing procedure.
Pairing mobile device:
LED indicator will light green after entering the level. Open ‘Pandora Online’ mobile application, go
to ‘Bluetooth Control’ –> ‘Not specified’ menu (‘Bluetooth device’ for iOS). This setting will be available
after adding the system in the account. The application will search for the system via Bluetooth connec-
