Panasonic WJSX550C - MATRIX SWITCHER, Руководство по эксплуатации

Страница: 86 / 130

●
Communication Speed
This table is used to set the parameters for communication between the System Controllers (or PCs) and the Matrix Switcher.
To program or edit the Communication Speed Table, do the following:
1. Move the cursor to position 3 by moving the Joystick Controller, then press the CAM (SET) key.
2. Move the Cursor to position 4 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window. Select the desired Baud Rate by moving the Joystick Controller,
and then press the CAM (SET) key to execute the selection.
3. Move the Cursor to position 5 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window. Select the desired Wait Time by moving the Joystick Controller,
and then press the CAM (SET) key to execute the selection.
4. Move the Cursor to position 6 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window. Select the desired Data Bit by moving the Joystick Controller,
and then press the CAM (SET) key to execute the selection.
5. Move the Cursor to position 7 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window. Select the desired Parity Check by moving the Joystick
Controller, and then press the CAM (SET) key to execute the selection.
6. Move the Cursor to position 8 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window. Select the desired Stop Bit by moving the Joystick Controller,
and then press the CAM (SET) key to execute the selection.
7. Move the cursor to position 9 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window. Select Address Control On or Off by moving the Joystick
Controller, and then press the CAM (SET) key to execute the selection.
8. Move the cursor to position 10 by moving the Joystick Controller.
Enter the desired Unit Number (1-16) by pressing the Numeric keys, and then press the CAM (SET) key to enter the Unit
Address.
9. Repeat the above procedures until the table is completed.
10. When all settings are completed, press the MON (ESC) key to escape from the programming mode.
The cursor returns to position 3.
90
4
S e t U p
F 1 : - - F 2 : - - F 3 : - - F 4 : P o p
S y s t e m S p e e d
C o m m u n i c a t i o n S p e e d
C U 1
U p
C U 2
B a u d
C U 3
C U 4
C U 5
C U 6
C U 7
C U 8
A L
P C
W a i t
T i m e
D a t a
B i t
P a r i t y
C h e c k
S t o p
B i t
F l o w
C o n t r o l
1 2 0 0
1 2 0 0
1 2 0 0
2 4 0 0
4 8 0 0
9 6 0 0
1 2 0 0
2 4 0 0
1 2 0 0
9 6 0 0 1 0 0
1 0 0
2 0 0
1 0 0
3 0 0
3 0 0
5 0 0
1 0 0
1 0 0 0
O f f
8
8
8
8
8
8
8
8
8
7 N o n e 1 N o n e
N o n e 1 N o n e
N o n e 1 N o n e
N o n e 1 N o n e
N o n e 1 N o n e
N o n e 1 N o n e
N o n e 1 N o n e
N o n e 1 N o n e
N o n e 1 N o n e
o d d 2 R S / C S
A d d r e s s
C o n t r o l
N o n e
N o n e
N o n e
N o n e
N o n e
N o n e
N o n e
N o n e
N o n e
O f f
1 U n i t N o .
R a t e
q w
e
r t y u
i o
!0