123. Program Out-1 COMP Output Connector
(PROGRAM OUT 1/COMP)
The Program Output Signal-1 of the composite video
signal is provided via this connector
.
124. Program Out-1 Y/C Output Connector
(PROGRAM OUT 1/Y/C)
The Program Output Signal-1 of the S-Video signal is
provided via this connector
.
125. Program Out-2 COMP. Output Connector
(PROGRAM OUT 2/COMP)
The Program Output Signal-2 of the composite video
signal is provided via this connector
.
126. Program Out-2 Y/C Output Connector
(PROGRAM OUT2/Y/C)
The Program Output Signal-2 of the S-Video signal is
provided via this connector
.
127. Preview Output Connector
(PREVIEW OUT, COMP.)
The effected video of the composite video signal is
obtained at this connector regardless of the selection
of the Program Out Buttons (15), (16), (17)
.
128. Black Burst Output Connector
(BLACK BURST OUT)
The Black Burst Signal for use with system
synchronization is provided via this connectorto the
Editing Controller
129. GPI Input Connector (GPI)
In the A/B Roll Editing System, the GPI signal (General
Purpose Interface) may be used in order to make
an interface between the WJ MX50 and the Editing
Controller
130. Cooling Fan
131. Main Power Switch (MAIN POWER)
The unit becames stand by mode by turning on this
switch. Unless this switch is turned on, the unit will not
be on even if the (front panel) Power ON/OFF Button
(1) is pressed.
Note:
The unit becomes on without pressing Power
ON/OFF Switch (1) by turning Main Power Switch
(131) on if the Reset ON/OFF Switch (109) had
been set to the OFF position. This takes place
leaving the Main Power Switch (131) off for more
than a few days
.
134. Program Out-2 Audio Output Jacks
(PROGRAM OUT 2/AUDIO, L/R)
The audio output signals of R channel and L-channel
on the Program Output 2 are provided via these jacks
.
135. Program Out-1 Audio Output Connectors
(PROGRAM OUT 1/AUDIO L/R)
The audio output signals of R-channel and L-channel
on the Program Outputi are provided via these
XLR-connectors
.
136. Auxiliary Audio Input-2 Jacks
(AUX AUDIO IN, AUX2)
The auxiliary audio input 2 signal can be inputted
via these jacks. When the audio is supplied to the
L-channel, this audio is supplied to tlie R channel
(mono-mode) internally.
When the audio is also
supplied to the R channel, this audio is used for the
R-channel only
.
137. Auxiliary Audio Input-1 Jacks
(AUX AUDIO IN,AUX1)
The auxiliary audio input 1 signal can be inputted
via these jacks. When the audio is supplied to the
L-channel, this audio is supplied to the R channel
(mono-mode) internally.
When the audio is also
supplied to the R-channel, this audio is used for the
R-channel only
.
138. Source 4 Audio Input Jacks
(SOURCE 4/AUDIO L/R)
Source 4 Audio Input signal can be supplied via these
jacks When the audio is supplied to the L channel,
this audio is supplied to the R-channel (mono mode)
internally
When the audio is also supplied to the
R-channel, this audio is used for the R channel only
139. Source 3 Audio Input Jacks
(SOURCE 3/AUDIO IN, AUX1)
Source 3 Audio Input signal can be supplied via these
jacks. When the audio is supplied to the L-channel, this
audio is also supplied to the R-channel (mono mode)
internally. When the audio is also supplied to the
R-channel, this audio is used for the R-channel only
.
140. Source 2 Audio Input Connectors
(SOURCE 2/AUDIO L/R)
The Source 2 Audio Input Signal can be supplied via
these XLR-connectors
.
141. Sourcel Audio Input Connectors
(SOURCE 1/AUDIO L/R)
The Sourcel Audio Input Signal can be supplied via
these XLR-connectors
.
- 1 3 -
132. Editing Control Connector
(EDITING CONTROLLER)
This connector is used for connecting with the Editing
Controller AG-A800 or the Modem Unit
.
133. RS422/RS232C Selection Switch
(RS422/RS232C)
When using an external product such as the Editing
Controller AG-A800 or the Modem Unit, this switch is
used to make the selection In the case of the Editing
Controller, turn this switch to the RS422 position In the
case of the Modem Unit, turn this switch to the RS232C
position
.
Содержание WJMX50 - MIXER
Страница 30: ... 29 ...
