-23-
■
Alarm Setup Menu
Move the cursor to ALARM SETUP on the SETUP
MENU, then press the SET button. The ALARM
SETUP menu appears on the monitor screen as
shown below.
1. Alarm Recall
There are 100 alarm records stored in chrono-
logical order in 10 pages of table.
The tables also indicate the alarm mode.
1. Move the cursor to ALM RECALL and press the
SET button. The ALARM RECALL table
appears on the monitor screen as shown
below.
4. To clear the alarm data, press the LEFT or
RIGHT button to select CLEAR where the cur-
sor is positioned, then press the SET button.
5. Press the SETUP/ESC button to return to the
previous ALARM SETUP menu.
2. Alarm Schedule
This item lets you enable or disable the system
alarm function.
1. Move the cursor to the ALM SCHEDULE para-
meter.
2. Select ON or OFF by pressing the LEFT or
RIGHT button. The initial factory setting is OFF.
ON:
Enables system alarm function.
OFF:
Disables system alarm function.
3. To set the timer, press the SET button while the
cursor is located on ON.
The table lists the active alarm modes (ALM-
MODE) as follows:
TRM
P
:
Interface Alarm
CH-LOSS:
Video Input Signal Loss Alarm
SITE:
Camera Site Alarm
PC
P
:
PC Command Alarm
2. Press the UP button to select the next page.
3. Press the DOWN button to back up to the pre-
vious page.
WJ-FS616 SETUP MENU
ALARM SETUP *
MULTI OUTPUT SETUP *
SPOT OUTPUT SETUP *
REC/MULTI2 REC OUTPUT *
SYSTEM SETUP *
CAM DOWNLOAD NO
CAM UPLOAD NO
ALL RESET SELECT *
ALARM RECALL 1 OF10
NO DATE TIME CAM ALM-MODE
10. 1.JAN97 12:00:00 16CH TRM 12
9. 12.DEC96 4:00:00 10CH SITE
8. 12.DEC96 3:00:00 8CH SITE
7. 12.DEC96 2:00:00 7CH SITE
6. 12.DEC96 1:00:00 6CH TRM 1
5. 11.DEC96 15:00:00 5CH TRM 5
4. 11.DEC96 14:00:00 4CH TRM 14
3. 11.DEC96 13:00:00 3CH TRM 7
2. 11.DEC96 12:00:00 2CH CH-LOSS
1. 11.DEC96 12:00:00 1CH CH-LOSS
DISPLAY (
“
)NEXT (
«
)PRE
CLEAR *
ALARM SETUP
ALM RECALL *
ALM SCHEDULE ON 0:00- 0:00
CAM SITE ALM OFF
SW-LOSS ALM OFF
ALM DISPLAY ON
ALM OUTPUT DUR 2SEC
ALM BUZZER DUR 2SEC
ALM MODE-MLT ALM-IND
DWELL TIME 2SEC
ALM MODE-SPT ALM-SPOT
DYNAMIC REC OFF
ALM REC MODE MODE0 REAL
ALARM SETUP
ALM RECALL *
ALM SCHEDULE OFF
CAM SITE ALM OFF
SW-LOSS ALM OFF
ALM DISPLAY ON
ALM OUTPUT DUR 2SEC
ALM BUZZER DUR 2SEC
ALM MODE-MLT ALM-IND
DWELL TIME 2SEC
ALM MODE-SPT ALM-SPOT
DYNAMIC REC OFF
ALM REC MODE MODE0 REAL
4. Press the UP or DOWN button to move the cur-
sor to the desired position, then adjust the time
when the alarm is to be activated by pressing
the LEFT or RIGHT button.
You can set the timer to extend into the next
day, for example, 22:00 - 6:00.
Note:
If the same time is set for start and stop
time, the alarm is always enabled.
5. Press the SETUP/ESC button to move the cur-
sor to ON position.
3. Camera Site Alarm
This item lets you enable or disable the camera site
alarm function.
1. Move the cursor to the CAM SITE ALM para-
meter.
2. Select ON or OFF by pressing the LEFT or
RIGHT button. The initial factory setting is OFF.
ON:
Enables camera site alarm function.
OFF:
Disables camera site alarm function.
Note:
To use this function, the WV-PB6164 Data
Multiplex Boards must be installed in the Video
multiplexer.
